Samsung AHU Series Service Manual Download Page 5

Precautions

1-2

Samsung Electronics

1-4 Others

ƒ

   Never store or load the air conditioner upside down or sideways to prevent the damage to the compressor.

ƒ

 Young children or infirm persons should be always supervised when they use the air conditioner.

ƒ

   Max current is measured according to IEC standard for safety.

ƒ

   Current is measured according to ISO standard for energy efficiency.

ƒ

  When installing, make sure there is no leakage. When recovering the refrigerant, ground the compressor first before removing the 

connection pipe. If the refrigerant pipe is not properly connected and the compressor works with the service valve open, the pipe 
inhales the air and it makes the pressure inside of the refrigerant cycle abnormally high. It may cause explosion and injury.

ƒ

   Pump Down Procedure (When removing the product)

- Turn on the air conditioner and select Cool mode to run the compressor for 3 minutes.

- Release the valve caps on High and Low pressure side.

- Use L wrench to close the valve on the high pressure side.

- Approximately 2 minutes after, close the valve on the low pressure side.

- Stop operation of the air conditioner.

- Disconnect the pipes.

All manuals and user guides at all-guides.com

Summary of Contents for AHU Series









































































Reviews: