Samsung AEX060EDEHA Installation Manual Download Page 35 | Manualshive

Page: 35 / 39

background image

35

EN

G

LIS

H

Trouble shooting

• Incorrect handling of thermostat, safety valve or other valves may lead to tank rupture. When servicing

the unit follow instructions carefully:

•  Always turn off main power supply when water supply is being shut off.
•  Test the free operation of the safety valve regularly by opening the valve ensuring the water flows freely.
•  Electrical connection and all servicing of the electrical components should only be carried out by an

authorized electrician.

• Fitting and all servicing of plumbing fixtures should only be carried out by an authorized installer.
• When replacing the thermostat, safety valve or any other valve or part supplied with this unit, use only

approved parts of the same specification.

Error codes

If the unit has some problems and does not work normally, error code is shown on the OUTDOOR UNIT main PBA

or LCD of the wired remote controller.

Display

Explanation

Error Source

101

Hydro-Unit / OUTDOOR UNIT wire connection error

HYDRO UNIT,

OUTDOOR UNT

162

EEPROM Error

HYDRO UNIT

201

Hydro-Unit/OUTDOOR UNIT communication error (Matching error)

HYDRO UNIT,

OUTDOOR UNT

202

Hydro-Unit/OUTDOOR UNIT communication error (3 min)

HYDRO UNIT,

OUTDOOR UNT

203

Communication error between MAIN and SUB PBA

OUTDOOR UNIT

221

OUTDOOR UNIT air temperature sensor error

OUTDOOR UNIT

231

Condenser temperature sensor error

OUTDOOR UNIT

251

Discharge temperature sensor error

OUTDOOR UNIT

320

OLP sensor error

OUTDOOR UNIT

403

Detection of OUTDOOR UNIT compressor freezing (During cooling operation)

OUTDOOR UNIT

404

Protection of OUTDOOR UNIT when it is overload (during Safety Start, Normal

operation state)

OUTDOOR UNIT

416

Discharge of a compressor is overheated

OUTDOOR UNIT

419

OUTDOOR UNIT EEV operation error

OUTDOOR UNIT

425

Power source line missing error (only for 3-phase model)

OUTDOOR UNIT

440

Heating operation blocked (outdoor temperature over 35°C)

OUTDOOR UNIT

441

Cooling operation blocked (outdoor temperature under 9°C)

OUTDOOR UNIT

458

OUTDOOR UNIT fan error

OUTDOOR UNIT

461

[Inverter] Compressor startup error

OUTDOOR UNIT

462

[Inverter] Total current error/PFC over current error

OUTDOOR UNIT

463

OLP is overheated

OUTDOOR UNIT

464

[Inverter] IPM over current error

OUTDOOR UNIT

WARNING

«
...
33
34
35
36
37
...
»

Summary of Contents for AEX060EDEHA








































Reviews:

No comments

Related manuals for AEX060EDEHA

Brand: Balcrank Pages: 8

Brand: NARVI Pages: 24

Brand: Waterous Pages: 10

Brand: Carrier Pages: 30

Brand: Firesense Pages: 16

Brand: Cozy Products Pages: 2

Brand: Salton Pages: 7

Brand: RADtec Pages: 7

Brand: Zenith Pages: 12

Brand: IceManCooler Pages: 2

Brand: nedis Pages: 36

Brand: VEAB Pages: 4

Brand: Oceanic Pages: 33

Brand: Wacker Neuson Pages: 64

Brand: Bard Pages: 49

Brand: QualityCraft Pages: 3

Brand: Grundfos Pages: 160

Brand: Berner Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands