Samsung AE050JXYDEH Service Manual Download Page 26

Page: 26 / 67

Samsung Electronics

Wired remote controller

(cont.)

Error mode

Contents

Measure

Product operation in

error condition

Error type

Outdoor unit/

Compressor/Control

Kit

PFC overload error

Check reactor located in control plate. If reactor is normal,

exchange INVERTER PBA.

Operation Off

Comp down

error

Input current sensor error

Check Input current sensor on Inverter PCB

Operation Off

Comp down

error

IPM is over heated

Check INVERTER PBA's temperature. Power off and cool

down INVERTER PBA, and then restart the outdoor unit.

Operation Off

Comp down

error

Gas leak error

Check the coolant charging status

Check the indoor EVA sensor

Check if the outdoor unit service value is open

Check that the indoor/outdoor installation pipe/wiring

are correct

Operation Off

Self diagnostic

error

Capacities not matched

Check the option code of the Control Kit

Operation Off

Outdoor unit

protection

control error

Option code miss matching

among the indoors(only for

DPM)

Option setting data is wrong.

(This error don't occur in EMF 150-AM).

Operation Off

Comp down

error

Inverter EEPROM loading error Check EEPROM DATA.

Check the normal operation of PCB.

Operation Off

Comp down

error

Communication error between

the Hydro Unit and wired

remote controller

Check the Control Kit PBA and wired remote controller

Operation Off

communication

error

Communication tracking error

between the Hydro Unit and

wired remote controller

Check the Control Kit PBA and wired remote controller

Operation Off

communication

error

Wired remote controller

temp sensor SHORT or OPEN

Check sensor connection status

Operation Off

wired remote

controller

sensor error

Memory(EEPROM) Read

Write error(Wired remote

controller data error)

Check the wired remote controller

Operation Off

communication

error

Water inlet (PHE) temp sensor

error (Short/Open)

Check sensor connection status.

Check sensor location. Check sensor resistance.

Operation Off

Indoor sensor

error

Water outlet (PHE) temp

sensor error (Short/Open)

Check sensor connection status.

Check sensor location. Check sensor resistance.

Operation Off

Indoor sensor

error

Water tank temp sensor error

(Short/Open)

Check sensor connection status.

Check sensor location.

Check sensor resistance.

Operation Off

Indoor sensor

error

Refrigerant gas inlet temp

sensor error (Short/Open)

Check sensor connection status.

Check sensor location. Check sensor resistance.

Operation Off

Indoor sensor

error

Flow switch open error

Check the junction point of Flow Switch terminal.

Check the junction point signal of Paddle operation after

the Flow Switch disassembly.

Check the water flow(Strainer clogging, Pump operation)

Operation Off

Comp down

error

Flow switch close error

Check the junction point of Flow Switch terminal.

Check the junction point signal of Paddle operation after

the Flow Switch disassembly.

Check the water flow(Strainer clogging, Pump operation)

Operation Off

Comp down

error

Thermostat wrong connection

error

Check the wiring of Hydro Unit Thermostat.

Check the Cooling /Heating signal : Concurrent wiring or

not.

Operation Off

Indoor sensor

error

Mixing valve temp sensor error

(Short/Open)

Check Control Kit Mixing Valve Outlet temperature sensor

location.

Operation Off

Indoor sensor

error

Summary of Contents for AE050JXYDEH




































































Search results

Summary of Contents for AE050JXYDEH

Reviews:

Related manuals for AE050JXYDEH

Brands by name

Popular brands

Samsung AE050JXYDEH, Service Manual

Search results

Summary of Contents for AE050JXYDEH

Reviews:

Related manuals for AE050JXYDEH

Brands by name

Popular brands