TXM20
PRODUCT SPECIFICATION SHEET
SERIES
DESCRIPTION
CATEGORY
TXM20
20 CHANNEL 1000W POWERED MIXER
SIGNAL PROCESSING
FEATURES
(continued)
>
1000-watt power amplifier section, featuring three modes
of operation; 2 x 500-watts Stereo Main, or 500-watt
Mono Main/500-watt Monitor, or 1000-watts Bridged
>
Ample inputs, the TXM20 has twelve mic/line inputs plus
four stereo line inputs.
>
Two Built-in, 24-bit DSP (Digital Signal Processor) Multi-
effects Processors with 100 selectable presets each
offering dazzling studio quality effects including Reverb,
Delay and Chorus and Flanging.
>
The TXM20 mixer features high-quality, low-noise
microphone pre-amplifiers that can accept signal from any
standard microphone. With the mixer’s XLR connectors,
connecting standard low impedance dynamic mics is
simple, and condenser microphones are connected easily
using the available 48 Volt Phantom Power.
ARCHITECT’S & ENGINEER’S SPECIFICATIONS
The Samson TXM20 shall be a 20 channel stereo powered
mixer. There shall be 12 mic/line channels and 4 stereo
channels. All mono channels shall have XLR inputs with
phantom power, Peak LED’s, 1/4 inch line inputs, insert
points, trim controls, high pass filters, 3 band EQ with
sweepable mids, 2 aux sends for moitors and 1 aux for the
onboard DSP, pan, mute, PFL and 60mm faders. Stereo
channels 13-16 shall have all the same controls except for
XLR inputs, insert points, High Pass and sweepable mids.
Channels 17-20 shall have aux sends 1 and 2, PFL, and level
only. The onboard DSP’s shall have 100 presets with aux 1
and 2 controls to add effects to monitors. The main section
shall have Aux 1 and 2 send faders, CD/Tape input fader,
Mono output/sub fader, and main level fader. There shall
be a channel 1-12 mute switch. There shall be a subwoofer
crossover in/out switch with frequency control for the mono/
sub output. There shall be an 11 segment LED ladder for
main level or AFL/PFL. There shall be a 9 band stereo graphic
EQ for the main outputs and a 9 band graphic EQ for the
monitors. There shall be a power amplifier capable of 2 x 500
watts @ 4 ohms or 1000 watts @ 8 ohms bridged mono.
489mm
520.06mm
144.76mm
FRONT
SIDE
TXM16 SPECIFICATIONS
Rated Output power .......................... 2 X 500W at 4Ω @0.1%
THD at 1KHz, 1 X 1000W at
8Ω Bridged
Frequency response .......................... 20Hz~20KHz+/-0.7dB@1W
Output into 8Ω (AMP OUT)
20 Hz~20KHz+/-0.4@+4dB
Output into 10kΩ (MAIN
OUT, MAIN OUT 2, AUX OUT,
AUX SEND, EFX OUT)
Total Harmonic Distortion .................. Less than 0.06% @ 20Hz~
20KHz, 75W output into4Ω
(SPEAKER OUT); Less than
0.1%@20 Hz~20KHz+4dBu
output into 10KΩ (MAIN
OUT, MAIN OUT 2, AUX OUT,
EFX OUT)
HUM & Noise ................................... -121dB equivalent input noise
(Average, RS+150Ω) ......................... -100dB residual output
noise (MAIN OUT, AUX OUT,
EFX OUT)
(with 22Hz~22KHz BPF) .................... -79dB (MAIN OUT, AUX
OUT) Master level control at
maximum, all channel level
control at minimum.
-79dB (EFX OUT) Master level
control at maximum, all channel
level controls at minimum.
Maximum Voltage Gain ...................... 67dB CH IN (MIC) to AMP OUT
63dB CH IN (MIC) to MAIN OUT, MONITOR OUT
54dB CH IN (MIC) to AUX 2 OUT
30dB CH IN (MIC) to REC OUT
32dB CH IN (LINE) to MAIN OUT, MONITOR OUT
26dB AUX IN to MAIN OUT
24dB TAPE IN to MAIN OUT
Crosstalk 1KHz ................................ 70dB adjacent input, 70dB
input to output
Input Channel Equalization
HIGH ................................. 12KHz shelving (+/- 15dB MAX)
MID ................................... variable 100 Hz to 8kHz
peaking (+/- 15dB MAX)
LOW .................................. 80Hz shelving (+/- 15dB MAX)
Meters ............................................ 11 POINT LED METERS (-20, -15,
-10, -7, -5,-3, 0, +1, +2, +4, +6dB)
Graphic Equalizer ............................. 9 bands (63, 125, 250, 500,
1K, 2K, 4K, 8K, 16KHz)
Internal DSP Effects ......................... 24 BIT - 10 Presets each: 1-
Performance; 2-Hall Reverb,
3-Plate Reverb; 4-Spring
Reverb; 5-Echo; 6-
Verb; 7- Verb; 8-Echo
+ Verb; 9-Chorus; 10-Flange
Phantom Power ................................ +48V
CLIP Indicators ................................ Turn on: THD> 0.1%
Foot Switch ..................................... DIGITAL EFFECT MUTE: ON/OFF
Power Requirement .......................... 110V/60 Hz, 240V/50Hz
(Country Specific)
Power Consumption .......................... 1900W, MAX.
Weight ............................................ 50.6 lbs./23Kg
Dimensions (W x H x D) .................... 24 1/2” x 6 1/4” x 21”
622mm x 159mm x 533mm