TXM16
PRODUCT SPECIFICATION SHEET
SERIES
DESCRIPTION
CATEGORY
TXM
16 CHANNEL 1000W POWERED MIXER
POWERED MIXERS
FEATURES
(continued)
>
Built-in, 24-bit DSP (Digital Signal Processor) Multi-
effects Processor with 100 selectable presets offering
dazzling studio quality effects including Reverb, Delay and
Chorus and Flanging.
>
The TXM16 mixer features high-quality, low-noise
microphone pre-amplifiers that can accept signals from any
standard microphone. With the mixer’s XLR connectors,
connecting standard low impedance dynamic mics is
simple, and condenser microphones are connected easily
using the available 48 Volt Phantom Power.
TXM16 SPECIFICATIONS
Rated Output power .......................... 2 X 500W at 4Ω @1% THD @
1KHz, 1 X 1000W at 8Ω Bridged
Frequency response .......................... 20Hz~20KHz+/-0.7dB@1W
Output into 8Ω (AMP OUT)
20 Hz~20KHz+/-0.4@+4dB
Output into 10kΩ (MAIN
OUT, MAIN OUT 2, AUX OUT,
AUX SEND, EFX OUT)
Total Harmonic Distortion .................. Less than 0.06% @ 20Hz~
20KHz, 75W output into 4Ω
(SPEAKER OUT); Less than
0.1%@20 Hz~20KHz+4dBu
output into 10KΩ (MAIN
OUT, MAIN OUT 2, AUX OUT,
AUX SEND, EFX OUT)
HUM & Noise ................................... -126dB equivalent input noise
(Average, RS+150Ω) ......................... -100dB residual output noise
(MAIN OUT, AUX OUT, EFX OUT)
(with 22Hz~22KHz BPF) .................... -73dB (MAIN OUT, AUX
OUT) Master level control at
maximum, all channel level
control at minimum.
-73dB (EFX OUT) Master level
control at maximum, all channel
level controls at minimum.
Maximum Voltage Gain ...................... 67dB CH IN (MIC) to AMP OUT
74dB CH IN (MIC) to MAIN OUT, MONITOR OUT
70dB CH IN (MIC) to AUX 2 OUT
52.2dB CH IN (MIC) to REC OUT
54dB CH IN (LINE) to MAIN OUT, MONITOR OUT
12dB AUX IN to MAIN OUT
24dB TAPE IN to MAIN OUT
Crosstalk, 1KHz ............................... 70dB adjacent input, 70dB
input to output
Input Channel Equalization
HIGH ................................. 12KHz shelving (+/- 12dB
Maximum) Mono & ST CH
MID ................................... Variable 80Hz to 8kHz
peaking (+/- 15dB Maximum)
Mono CH 2.5kHz peaking
(+/-12dB) Maximum ST CH
LOW .................................. 80Hz shelving (+/- 12dB
Maximum) Mono & ST CH
Meters ............................................ 11 POINT LED METERS (-20, -15,
-10, -7, -5,-3, 0, +1, +2, +4, +6dB)
Graphic Equalizer ............................. 9 bands(63,125, 250,500,1K,
2K, 4K, 8K, 16KHz) +/-12dB
Internal DSP Effects ......................... 24 BIT - 10 Presets each:
1 - Performance; 2 - Hall Reverb,
3 - Plate Reverb; 4 - Spring
Reverb; 5 - Echo; 6 -
Verb; 7 - Verb; 8 - Echo
+ Verb; 9- Chorus; 10- Flange
Phantom Power ................................ +48V
PEAK Indicators ............................... Turn on: 5dB before clipping
Foot Switch ..................................... DIGITAL EFFECT MUTE: ON/OFF
Power Requirement .......................... 120V/60 Hz, 240V/50Hz
(Country Specific)
Power Consumption .......................... 500W, 1/8 Power
Weight ............................................ 42.9 lbs./19.5Kg
Dimensions (W x H x D) .................... 19 1/4” x 5 3/4” x 21 1/2”
489mm x 145mm x 520mm
ARCHITECT’S & ENGINEER’S SPECIFICATIONS
The Samson TXM16 shall be a 16 channel stereo powered
mixer. There shall be 8 mic/line channels and 4 stereo
channels. All mono channels shall have XLR inputs with
phantom power, Peak LED’s, 1/4 inch line inputs, insert
points, trim controls, high pass filters, 3 band EQ with
sweepable mids, 2 aux sends and 1 aux for the onboard DSP,
pan, mute, PFL and 60mm faders. Stereo channels 9-12
shall have all the same controls except for XLR inputs, insert
points, High Pass and sweepable mids. Channels 13-16 shall
have aux sends 1 and 2, PFL, and level only. The onboard
DSP shall have 100 presets with aux 1 and 2 controls to add
effects to monitors. The main section shall have Aux 1 and
2 send faders, CD/Tape input fader, Mono output/sub fader,
and main level fader. There shall be a subwoofer channel 1-8
mute switch. There shall be a crossover in/out switch with
frequency control for the mono/sub output. There shall be
an 11 segment LED ladder for main level or AFL/PFL. There
shall be a 9 band stereo graphic EQ for the main outputs and
a 9 band graphic EQ for the monitors. There shall be a power
amplifier capable of 2X500 watts @ 4 ohms or 1000 watts @
8 ohms bridged mono.
489mm
520mm
FRONT
145mm
SIDE
