Guided Tour - Rear Panel
1: Power on-off switch
- As you may have guessed, this is what you use to turn the
PL 2404 on and off. To avoid potential damage to your speakers, turn the PL 2404 on
before
you turn on any connected power amps—and turn it off
after
the power amps are
turned off.
2. Fuse -
Contains a 1 amp, 250 volt fuse.
3. AC input
- Connect the supplied standard 3-pin “EEC” plug here.
4: Bus out
(1 - 4) - These unbalanced outputs allow you to route signal from each of the
four discrete buses to external devices such as a multitrack digital or analog tape
recorder. The signal is post-bus fader but pre-Main control. See the “Busing,
Submixing, and Channel Muting” section in this manual for more information.
5: Main Out
(L, R) - These are the PL 2404’s main outputs. In live performance
applications, you’ll usually use these to connect the PL 2404 to a power amp and
speakers; in recording applications, these will normally be connected to the inputs of a
two-track recorder. The Main out jacks are electronically balanced, so you should use
balanced three-conductor cabling and 1/4" TRS plugs wherever possible (unbalanced
two-conductor plugs can also be inserted into these outputs, but you’ll get better signal
quality and less outside noise and hum if you use balanced lines). See the “Connecting
the PL 2404” section on page 10 for more information.
6: Control Room Out
(L, R) - In recording applications, these will normally be
connected to a power amplifier and loudspeakers. The Control Room out jacks are
electronically balanced, so you should use balanced three-conductor cabling and 1/4"
TRS plugs wherever possible (unbalanced two-conductor plugs can also be inserted into
these outputs, but you’ll get better signal quality and less outside noise and hum if you
use balanced lines). See the “Connecting the PL 2404” section on page 10 in this
manual for more information.
8
PL 2404 24 CHANNEL PROGRAM STEREO / LINE MIXER
SAMSON
3
1
2
4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
BUS OUTPUTS
UNBALANCED
<75
Ω
+4dBu
R
CONTROL ROOM
BALANCED <75
Ω
+4dBu
LINE INPUTS - BALANCED 10K
Ω
+4dBu
S/N
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
!
115V - 60 Hz 25W
POWER
RATING
AVIS:
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
DO NOT EXPOSE THIS EQUIPMENT
TO RAIN OR MOISTURE
MAIN
BALANCED <75
Ω
+4dBu
LEFT / MONO
RIGHT
1
2
3
4
1
2
3
4
1
2
3
4
BUS INSERTS
UNBALANCED <75
Ω
+4dBu
MIXER LINKING
AUX SENDS
UNBALANCED <75
Ω
+4dBu
AUX RETURNS
STEREO INPUTS
UNBALANCED 10K
Ω
+4dBu
1
2
3
4
INSERT
L
1
2
3
MIC 1
1
2
3
MIC 3
ON
OFF
~AC INPUT
115V, 60Hz
25W
1
9
8
10
2
3
4
6
5
7
11
13
12
TRS
STEREO INPUT
TIP = LEFT
RING = RIGHT
SLEEVE = COM
TRS
BALANCED
TIP = HI
RING = LO
SLEEVE = COM
TRS INSERT
UNBALANCED
TIP = RETURN
RING = SEND
SLEEVE = COM
XLR
BALANCED
3 = LO
2 = HI
1 = COM
+4
-10
0
−50
+4
-10
0
−50
POWER
FUSE
1A/250V
R
L
Summary of Contents for PL2404
Page 1: ......