Samson Media 7 Mounting And Operating Instructions Download Page 69

Page: 69 / 96

EB 9510 EN

Malfunctions

10 Malfunctions

Malfunctions are indicated on the display by error messages in conjunction with an icon for

status classification and an error ID. The meaning of the icons and their order of priority are
listed in Table 7.

Table 7:

Icon showing status classification

Status icon

Priority

Meaning

Failure

Out of specification

Maintenance required

No message

On the start screen, error messages can be cleared by pressing the

key. Error messages

and recommended action for troubleshooting are listed in Table 8.

Table 8:

Troubleshooting

Error ID

Message

Possible causes and recommended action

101

AMR magnet lost

The Media 7 device has an internal device error.

Contact SAMSON's After-sales Service.

102

AMR sensor not recognized

103

Memory error (calibration)

104

Memory error (data)

105

No factory calibration

106

Pressure sensor error

107

Internal data processing error

201

AMR signal outside range

Reset the Media 7 device. Contact

SAMSON's After-sales Service when this

error reoccurs.

202

Measuring span error

Check the settings for the tank and media

data. Correct them, if necessary.

203

Characteristic error

An invalid tank geometry has been entered:

Re-enter tank data (only possible in TROVIS-

VIEW).

Summary of Contents for Media 7

































































































Search results

Summary of Contents for Media 7

Reviews:

Brands by name

Popular brands

Samson Media 7, Mounting And Operating Instructions

Search results

Summary of Contents for Media 7

Reviews:

Brands by name

Popular brands