background image

5-4  

EB 9510 EN

Installation

5.3.2  Setting up the standby 

power supply (SPS)

The battery is not included in the scope of 

delivery.

Operation with standby power supply (SPS) 
is restricted as follows:

 

Î

The 

GSM module

 does not function in 

SPS mode.

 

Î

The 

AIA: Analog input active option 

module

 does not supply any voltage.

The use of unapproved batteries will dam-

age the gateway.

 

Î

Do not use rechargeable batteries in the 

gateway.

The standby power supply can also be used 
during the first start-up when no other power 
supply is available. A lithium battery allows 
the device to run for approx. seven days.

To continue to supply the power supply unit 
with power after a power failure, we recom-
mend using a battery with the following 

specifications:

 

AA lithium battery (mignon), 1.5 V

 

Industrial battery with long service life 

(min. 3000 mAh recommended)

 

Suitable for temperatures from –40 to 
+60 °C

Inserting the battery

1. 

Place the 1.5 V battery in the battery 
compartment (see Fig. 5-2)

 

Î

Observe the correct polarity.

 A battery 

symbol with plus and minus signs on the 
battery compartment indicates the polar-
ity.

Note

NOTICE

!

Tip

Summary of Contents for 5007-2 Series









































































Reviews: