background image

Contents

Page

1

Design and principle of operation

.  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 4

2

Assembling and adjusting valve and actuator

.  .  .  .  .  .  .  .  .  .  .  .  .  .  . 6

2.1

Option to pretension the springs for actuator version
"Actuator stem extends" .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 7

2.2

Valve and actuator that have different rated travels .  .  .  .  .  .  .  .  .  .  . 7

3

Installation

.  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 8

3.1

Mounting position .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 8

3.2

Signal pressure line.  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 8

4

Operation

.  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 8

5

Maintenance

.  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 8

5.1

Replacing packing, seat, and plug .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 9

6

Version with split plug stem extension

.  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 11

7

Customer inquiries

.  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 13

2

EB 8093 EN

Contents

Note:

Non-electrical actuators and valves do not have their own potential ignition source
according to the risk assessment in the rare incident of an operating fault, corresponding to
EN 13463-1: 2001 paragraph 5.2, and therefore do

not

fall within the scope of the

European Directive 94/9/EC.
Refer to paragraph 6.3 of EN 60079-14:1977 VDE 0165 Part 1 concerning connection to
equipotential bonding system.

Summary of Contents for 3248-1

















Reviews: