background image

EB 2522 EN 

 21

Mounting and start-up

5.1.2  Mounting orientation

Standard

Preferably install the regulator in a horizon-
tal pipeline. The actuator housing with set 
point adjuster must face upwards.

Fig. 6: 

Installation in 

horizontal 

pipelines

 

Î

Install the control line to the tapping 

point with an approx. 10 % slope to al

-

low any condensing liquid to flow back 

into the tank or pipe.

Options

Alternatively, the valve can be installed in a 
vertical pipeline. The actuator housing with 
set point adjuster must face sideways.

Fig. 7: 

Installation in 

vertical pipelines

Control deviations due to alternative instal-

lation.

System deviations may arise when the regu

-

lator is installed in vertical pipelines.

NOTICE

!

5.1.3 

Additional fittings

Strainers

We recommend installing a strainer (e.g. 
SAMSON Type 2 N) upstream of the regula

-

tor. It prevents solid particles in the process 
medium from damaging the valve.

 

Î

Install the strainer upstream of the tem-
perature regulator. The arrow on the 

valve indicates the direction of flow.

 

Î

For installation in vertical pipeline: install 

the strainer with the filter element facing 

downwards.

 

Î

Install the filter with sufficient space avail

-

able to remove the filter.

 

Î

Check the strainer at regular intervals 
and clean it, if necessary.

Shut-off valves

Install a hand-operated shut-off valve both 
upstream of the strainer and downstream of 
the regulator. This allows the plant to be shut 
down for cleaning and maintenance, and 
when the plant is not used for longer periods 
of time.

Pressure gauges

Install a pressure gauge both upstream and 
downstream of the regulator to monitor the 
pressures prevailing in the plant.

Summary of Contents for 2406

































Reviews: