SamplexPower PST-1000-12 Owner'S Manual Download Page 15

14  |  SAMLEX AMERICA INC.    

 

    

SAMLEX AMERICA INC.  |  15

SECTION 2  |  

General Information

TABLE 2.1: INVERTER SIZING FACTOR
Type of Device or Appliance

Inverter  

Sizing Factor 

(See note 1)

Air Conditioner / Refrigerator / Freezer (Compressor based)

5

Air Compressor

4

Sump Pump / Well Pump / Submersible Pump

3

Dishwasher / Clothes Washer

3

Microwave (where rated output power is the cooking power)

2

Furnace Fan

3

Industrial Motor

3

Portable Kerosene / Diesel Fuel Heater

3

Circular Saw / Bench Grinder

3

Incandescent / Halogen / Quartz Lamps

3

Ceramic/ Positive Temperature Coefficient (PTC) type of heaters

5

Laser Printer / Other Devices using Infrared Quartz Halogen Heaters

4

Switch Mode Power Supplies (SMPS): no Power Factor correction

2

Photographic Strobe / Flash Lights

4 (See Note 2)

NOTES FOR TABLE 2.1   

1.   Multiply the Rated Continuous Running Power Rating of the appliance / device by the 

recommended Sizing Factor to arrive at the Rated Continuous Running Power Rating 
of the inverter. 

2.   For photographic strobe / flash unit, the Surge Power Rating of the inverter should be  

> 4 times the Watt Sec rating of photographic strobe / flash unit.

Summary of Contents for PST-1000-12





















Reviews: