background image

2 YEAR Limited Warranty

The BBM-1225 manufactured by Samlex America, Inc. ( the “ Warrantor “ ) is warranted to be free

from defects in workmanship and materials under normal use and service.  This warranty is in effect

for 2 years from the date of purchase by the user ( the “ Purchaser “)

For a warranty claim, the Purchaser should contact the place of purchase to obtain a Return Authoriza-

tion Number.

The defective part or unit should be returned at the Purchaser’s expense to the authorized location.  A

written statement describing the nature of the defect, the date of purchase, the place of purchase, and

the Purchaser’s name, address and telephone number should also be included.

If upon the Warrantor’s examination, the defect proves to be the result of defective material or work-

manship, the equipment will be repaired or replaced at the Warrantor’s option without charge, and

returned to the Purchaser at the Warrantor’s expense.

No refund of the purchase price will be granted to the Purchaser, unless the Warrantor is unable to

remedy the defect after having a reasonable number of opportunities to do so.

Warranty service shall be performed only by the Warrantor.  Any attempt to remedy the defect by

anyone other than the Warrantor shall render this warranty void.

There shall be no warranty for defects or damages caused by faulty installation or hook-up, abuse or

misuse of the equipment including exposure to excessive heat, salt or fresh water spray, or water

immersion.

No other express warranty is hereby given and there are no warranties which extend beyond those

described herein.  This warranty is expressly in lieu of any other expressed or implied warranties,

including any implied warranty of merchantability, fitness for the ordinary purposes for which such

goods are used, or fitness for a particular purpose, or any other obligations on the part of the Warrantor

or its employees and representatives.

There shall be no responsibility or liability whatsoever on the part of the Warrantor or its employees

and representatives for injury to any persons, or damage to person or persons, or damage to property,

or loss of income or profit, or any other consequential or resulting damage which may be claimed to

have been incurred through the use or sale of the equipment, including any possible failure of mal-

function of the equipment, or part thereof.

The Warrantor assumes no liability for incidental or consequential damages of any kind.

Samlex America Inc. (the “Warrantor”)

110-17 Fawcett Road

Coquitlam BC V3K6V2 Canada

(604) 525-3836

Page 10

Summary of Contents for BBM-1225













Reviews: