manualshive.com logo in svg

samlexsolar SCC-30AB, Owner'S Manual, Page: 36 / 48

Share
Download
samlexsolar SCC-30AB Owner'S Manual Download Page 36

36

6

INSTALLATION & OPERATION

6. Connect the Solar Panel (Module)/Array next. The green LED indicator will light if 

the Solar Panel (Module)/Array is connected during the daytime and the Solar Panel 
(Module)/Array is wired correctly. 

•  Remember that the Solar Panel (Module)/Array will generate power whenever in 

sunlight. Also, be careful not to short circuit the Solar Panel (Module)/Array while 
connected to the controller, since this will damage the controller.

7. For most effective surge protection, it is recommended that the Negative system 

conductor be properly grounded.

Dip Switch Settings 

Five DIP Switches permit the following parameters to be adjusted at the installation 

site: 

DIP Switch 1

ON

*

Selection of battery voltage for 12V system

OFF

Selection of battery voltage for 24V system

DIP Switch 2, 3,  4

Battery charge control mode: Battery charging algorithm (see Table 6.1)

DIP Switch 5

ON

Selection of Auto Equalization

OFF

*

Selection of Manual Equalization

*NOTE: Factory preset condition

     

Battery Charging Notes

The SCC-30AB manages many different charging conditions and system 

configurations. Some useful functions to know are given below.

Solar Overload:

 Enhanced radiation or “edge of cloud effect” conditions can 

generate more current than the controller’s rating. The Budget will reduce this 
overload up to 130% of rated current by regulating the current to safe levels. If the 
current from the solar array exceeds 150%, the controller will interrupt charging.

Battery Types:

 The SCC-30AB’s standard battery charging programs are suitable for 

a wide range of Lead-Acid battery types. These standard programs are select by DIP 
Switch 2~4. 

Summary of Contents for SCC-30AB

















































Reviews:

No comments