manualshive.com logo in svg

Samcon ExCam IP1354, User Manual, Page: 18 / 44

Share
Download
Samcon ExCam IP1354 User Manual Download Page 18

 
 
 

 
 

Doc.-ID: 141021-PT08BA-TG-ExCam IP13xx Series_en_rev.03, page 18 of 44 

5 

Commissioning 

 

Attention! 
Please  observe  the  national  regulations  regarding  security,  installa-
tion, and accident prevention (e.g. DIN EN 60079-14 or DIN VDE 0118-
1:2010-02) for the erecting of electrical plants in mining etc.) as well as 
the safety guidelines described in this user manual and the EX instal-
lation manual!

 

 

 

Attention! 
Please observe the installation and commissioning advices described 
in the ATEX/ IECEx/ EAC-Ex Ex-installation manual! 

 
 
 

5.1 

Step 1: Installation 

 
Install the ExCam

®

 IP13xx at the desired location. 

Mounting options and conditions, accessories, as well as safety guidelines are described 
in the EX installation manual of the T08 ExCam

®

 Series. 

 

5.2 

Step 2: Electrical connection 

 

 

Attention! 
The electrical connection of the equipment must be executed by quali-
fied personnel only! 

 

Attention! 
It  is  mandatory  that  the  housing  of  the  ExCam

®

  Series  has  to  be 

grounded via a PE-connection!

 

 

Attention! 
The  minimum  cable  length  of  the  connection  line  must  not  be  less 
than  one  meter!  The  connection  cable  has  to  be  laid  in  a  protected 
manner! 

 

Attention! 
Please  observe  the  national  regulations  regarding  security,  installa-
tion, and accident prevention (e.g. DIN EN 60079-14 VDE 0118-1:2010-
02 etc.), as well as the safety guidelines described in this user manual 
and the EX installation manual!

 

 

 
 

Summary of Contents for ExCam IP1354













































Reviews:

No comments