manualshive.com logo in svg

Sam 271, Directions For Use Manual

Share
Download
Sam 271 Directions For Use Manual Download Page 8

8

Product Support 

1-888-202-9831

4.  Features of the 

sam

 Device

4.1. PRESET TREATMENT

The 

sam

 Device is preconfigured to provide continuous ultrasonic output at a preset 

frequency and intensity which cannot be modified by the user. The user can set the 
treatment duration to be 1, 2, 3, or 4 hours. 

4.2.

 

sam ULTRASOUND APPLICATORS

 

The 

sam

 Ultrasound Applicators serve as the ultrasound transducers of the  

sam

 Device. The applicators offer low-profile design with light emitting diode (LED) on/

off notification. The ergonomic plastic housing and smooth contours provide  
enhanced comfort.

4.3. sam SENSING

sam

 is designed to work with the human body and maximize the safe and effective 

delivery of long-duration therapeutic ultrasound. Each 

sam

 Applicator is equipped 

with closed-loop continuous temperature monitoring which maintains treatment site 
temperatures below 44°C during normal operation. See section 13.4 on page 24 for 
more information.

4.4. sam ULTRASOUND COUPLING Patches

The 

sam

 Device utilizes ultrasound coupling Patches which are manufactured with 

ultrasound coupling media sealed inside. The ultrasound coupling Patches ARE 
REQUIRED to secure the 

sam 

Applicators to the body. 

4.5. BATTERY OPERATION

Powered by a rechargeable lithium-ion battery, the 

sam

 Device can provide  

4 hours of therapy on a single battery charge.

Summary of Contents for 271





































Reviews:

No comments

Brands by name

Popular brands

Load more brands