SINK
3
1
/
2
" - 4" SINK
OPENING
HEX METAL
WASHER (S5028F)
SPRING STEEL SNAP RING
RETAINER (S5028LS)
S.S. HEX HEAD BOLTS (997031)
RUBBER STOPPER (5088)
S.S. SINK
ADAPTOR
(S5028)
GASKET (S5028G)
O-RING (568237)
SINK COLLAR (70C)
2
Typical Installations
Installation of CONE BOWL or SINK COLLAR
INCOMING POWER
CONTROL
SOLENOID VALVE
WITH FLOW CONTROL
VACUUM
BREAKER
OPTIONAL
SHORT LEG
SINK
OPTIONAL
SHORT TOP
HOUSING
INCOMING WATER
3
/
4
" PLUMBING
REDUCED TO
1
/
2
"
1
/
2
" VALVE
(NF)
1
/
2
" PLUMBING
WATER
INLET
2" DRAIN
(models 100-200)
2" OR 3" DRAIN
(models 300-500)
INCOMING POWER
CONTROL
SOLENOID VALVE
WITH FLOW CONTROL
VACUUM
BREAKER
WATER
INLET
OPTIONAL
PRE-RINSE
CONE
INCOMING WATER
3
/
4
" PLUMBING
REDUCED TO
1
/
2
"
1
/
2
" VALVE
(NF)
1
/
2
" PLUMBING
2" DRAIN
(models 100-200)
2" OR 3" DRAIN
(models 300-500)
INCOMING POWER
CONTROL WITH
(P) OR (PP) OPTION
OPTIONAL
REMOTE
START/STOP
VACUUM
BREAKER
WATER
INLET
CONE OR SINK
INCOMING WATER
3
/
4
" PLUMBING
REDUCED TO
1
/
2
"
1
/
2
" VALVE
(NF)
1
/
2
" PLUMBING
(P)
(PP)
2" DRAIN
(models 100-200)
2" OR 3" DRAIN
(models 300-500)
Models 300 through
500 furnished with
single support leg.
CONE ASSEMBLY
1.
Cut a hole in the counter top using the appropriate table
cutout dimensions listed below.
2.
Place the large open end of the cone bowl against the un-
derside of the counter top and weld the flange. Weld all the way
around and then buff smooth for a watertight, sanitary installation.
SINK COLLARS:
6
1
⁄
2
” Sink Collar #65
1.
If necessary, cut a 6 5/8” DIAMETER hole in the center of the
bottom of the sink.
2.
Place the adaptor against the underside of the sink and weld all
the way around. Buff smooth for a watertight, sanitary installation.
WELD IN SINK
COLLAR (65)
SINK
LARGE RUBBER
STOPPER (LRS)
6
5
/
8
” SINK
OPENING
#65 SINK COLLAR
#70 SINK COLLAR
3
1
⁄
2
” Sink Collar #70
1.
Apply caulking compound around the sink hole (TOP SIDE).
2.
Insert the stainless steel adaptor in the sink hole.
3.
Place the gasket over the stainless steel adaptor (UNDER
SINK).
4.
Place the hex metal washer over the stainless steel adaptor,
up against the gasket.
5.
Place the sink collar with O-ring inserted over the stainless
steel adaptor, up against the hex metal washer.
6.
Slip the spring steel snap ring over the bottom of the stain-
less steel adaptor and slide up until it snaps into the groove in
the stainless steel adaptor.
7.
Screw the hex head bolts out of the sink collar and up against
the hex metal washer tight enough to firmly set the assembly.
8.
The disposer rubber adaptor fits over the sink collar and
bands to the sink collar.
WARNING: Never put your hand thru the Sink Collar
after being installed as injury is possible.
Application
Cutout Size
12” Cone Bowl
12
7
⁄
8
” Diameter
15” Cone Bowl
15
7
⁄
8
” Diameter
18” Cone Bowl
18
7
⁄
8
” Diameter
