background image

 

11 

3. 

To give a ‘flat top’ look, the hair on the top of the head must be cut over the top of 

a flat comb rather than by using the attachment comb. 

4.  Use the closer cutting attachment combs to taper the hair down to the decline as 

desired. Comb hair and check for uneven areas and outlining sideboards and 

necklines as described previously. 

 

CLEANING AND MAINTENANCE 

  This appliance is for household use only and is not user-serviceable.  

  Do not open or change any parts by yourself. Please refer to a qualified electrical 

service department or return to the supplier if servicing is necessary. 

  Always  remember  to  unplug  the  unit  from  the  electrical  outlet  when  not  in  use 

and before cleaning. Ensure that the speed control is set to “0”.  

  It  is  much  easier  to  clean  the  accessories  directly  after  they  have  been  used. 

Wash them in warm, soapy water, rinse and dry well. 

  The  body  of the  appliance  and  the stand should  be  cleaned  with  a  damp  cloth. 

Do not let water enter the appliance or the stand. 

  Do  not  use  bleach  or  other  abrasive  substance  or  solvents  to  clean  your 

appliance as it can be damaging to the finish. 

  Do  not  immerse  the  appliance  in  water  or  any  other  liquid,  or  hold  it  under  a 

running tap to clean. 

  To  remove  stubborn  spots/marks,  wipe  the  surfaces  with  a  cloth  slightly 

dampened  in  soapy  water  or  mild  non-abrasive cleaner.  Rinse  and  dry a  clean, 

dry, soft cloth. 

 

 

Summary of Contents for SHC11















Reviews: