manualshive.com logo in svg

Salini SCG-6182B, Instruction Manual, Page: 19 / 22

Share
Download
Salini SCG-6182B Instruction Manual Download Page 19

-18- 

 

After each use 

•

 

Wipe the appliance over with a damp cloth. 

•

 

Dry the appliance by rubbing the surface with a clean cloth.

 

 

 

IMPORTANT:

 DO NOT use any corrosive cleaning products or abrasive cleaners. Only clean 

with warm water and a small amount of washing-up liquid. 

 

 

CAUTION! 

Ensure the heating plate is clean. A soiled zone does not transfer all of the heat. 

Protect the hob against corrosion. Switch off the hob when not in use. 

Do not leave pans with prepared dishes based on fats and oils unattended on the 

switched on plate; hot fat can spontaneously catch fire. 

 

 

IMPORTANT: 

 

If your appliance appears not to be operating correctly, please make contact with the 

dealer.

 

 

 

 

DO NOT ATTEMPT TO REPAIR THE APPLIANCE YOURSELF!

 

 

Please note that if an engineer is asked to attend whilst the product is under guarantee and 

finds that the problem is not the result of an appliance fault, then you may be liable for the 

cost of the call out charge. 

 

The appliance must be accessible for the engineer to perform any necessary repair. If your 

appliance is installed in such a way that an engineer is concerned that damage will be 

caused to the appliance or your kitchen, then they will not complete the repair.  

 

 

 

Summary of Contents for SCG-6182B























Reviews:

No comments