background image

 

SALEEN SERIES VI SUPERCHARGER FOR 2005-07 MUSTANG

 

MAINTENANCE SCHEDULE 

Very little maintenance is required for your Series VI supercharger. There are two key 

fluids involved in the kit which you should pay attention to. Please hold on to the 

installation manual for the supercharger kit to aid in the location and identification of the 

components 

1. The oil in the front (gear case) of the supercharger is refilled via a brass plug on the 

driver’s side. The plug is underneath the water crossover of a completely installed kit. The 

supercharger takes a full pint of oil. The oil that the supercharger is delivered with will last 

50,000 miles. A 5W-50 oil may be substituted but will need to be changed every 5000 

miles. When changing the oil, be sure to completely siphon all of the oil out of the gear 

case. 

2. The supercharger kit comes complete with an independent coolant system. Regularly 

check the fluid level of the intercooler system. The fluid should reach the bottom of the 

neck of the recovery tank when the system is cold. With the water pump on (key on or car 

on), check as often as every couple of oil changes that the fluid is circulating. If it is not, 

purge the system per the instructions in the supercharger installation manual.  

Change the fluid in the intercooler system as often as the radiator fluid is changed, using a 

50/50 mix of antifreeze and water.  

If you have any questions, please call Saleen at 

248

-

743

-

4800

 

 

 

 

*note: there is no warranty on the supercharger in the aftermarket unless supplied by the 

installer. 

 

 

 

Summary of Contents for VI Series










Reviews: