Salamander Pumps HomeBoost Installation Manual Download Page 4

3

Points applicable to 

whole house 

installation:

Points applicable to 

combi-boiler 

installation:

Do’s

   HomeBoost

 must be fitted to rigid fixed 

pipework preferably with vertical inlet  
and outlet

  Pipework above and below the pump must 

be securely fixed to the wall

  Only one HomeBoost

 may be fitted per 

household supply

  Ensure that installation complies with IET 

Wiring Regulations

  Allow 100mm on all sides for ventilation
  Ensure pump is protected from frost
  Complete all hot work fitting prior to 

HomeBoost

 installation

  We recommend that the pump is activated 

for at least five minutes every four weeks

  If the supply is known to be lime/calcium 

(hard) water, fit extra filtration before the 
pump

Do’s

  Install vertically or horizontally, mounted 

on cold water mains inlet to the house

  Locate the pump next to the mains  

stop tap

  Pump should be fitted before ANY other 

water outlets taken after the mains stop 
tap. If any outlets are between the stop tap 
and your HomeBoost

, they must be fitted 

with a non-return valve (NRV)

Do’s

   Install vertically or horizontally, mounted 

on cold water mains inlet to the combi 
boiler

  Locate the pump next to the combi-boiler 

OR on it’s cold water mains inlet

  Pump must exclusively feed the  

combi-boiler

Don’ts

   Never fit to hot water piping
  Never fit the pump to communal risers
  Never pump directly from or to another 

pump – only one HomeBoost

 may be 

installed per household supply

  Never fit to flexible pipework (e.g. tap 

connectors)

   HomeBoost

 cannot be used on outside 

coldwater storage tanks, bore holes or 
wells

  Never use jointing compounds,  

Boss White, hemp or steel wool

  Solder fluxes must not come into contact 

with the pump

  Never fit to restrictive or collapsed supply 

(eg lead main)

Pre-installation checklist

HomeBoost

 is suitable for two separate types of water boosting applications

1  Boosting the incoming mains water supply to a whole house 
2  Boosting the inlet mains water supply solely to a combination (combi) boiler.

Points applicable to 

either installation

 type:

x142741_SP_p4_vw.indd   4

07/01/2015   14:26

Summary of Contents for HomeBoost

















Reviews: