manualshive.com logo in svg

SAINT-GOBAIN NORTON clipper CR16, Operating Instructions Manual, Page: 12 / 15

Share
Download
SAINT-GOBAIN NORTON clipper CR16 Operating Instructions Manual Download Page 12

VERS. 01.09.2019 

CR16 _MAN_EN 

 
 
 
 

12 
 
 
 
 

7-FAULT: CAUSES AND CURES 

 

7.1 Fault –finding procedures 

Should any fault occur during the use of the machine, turn it off. Any works dealing with the engine 
of the machine can only be carried out by a qualified technician. 
 

 

7.2 Troubles-shooting guide 

TROUBLE 

POSSIBLE CAUSE 

REMEDY 

Engine won't start. 

Insufficient fuel. 

Refuel with Automotive 
gasoline. 

Fuel Cock is closed. 

Open the fuel cock. 

Engine Switch is set to 

OFF 

Set the switch to ON. 

position. 
Spark Plug contaminated 

Replace the spark plug. 

or damaged. 
Improper spark plug gap 

Correct the gap. 

Engine stops suddenly, 

Main jet of the carburetor 

Take out the main jet from 

being clogged with dirt. 

carburetor, and clean the 

  

the jet with compressed 

air. 

Air Filter Element dirty. 

Clean the element. 

Spark Plug cap is loose. 

Tightly fit the plug cap 
to the plug. 

Engine runs, but the machine  

Lack of engine power. 

See above. 

Clutch slipping. 

Dismantle the clutch 

 

assembly, and clean the 

 

shoe and drum with pro- 

 

per solvent.  Replace the 

  

shoe if necessary. 

Crank/Gear unit damaged.  Contact dealer. 

 

 
 
 
 
 
 
 

Summary of Contents for NORTON clipper CR16
















Reviews:

No comments