Sailrite Leatherwork 3008-00 Assembly Instructions Manual Download

Page: 2 / 13

Table of Contents

Leatherwork

Legs & Tabletop Components ��1

Tabletop & Legs 1
Tabletop & Legs Hardware 2

Leatherwork

Sewing Machine Components ��3

Head Box  3
Servo Motor  4
Accessories  4

Assembling the Leatherwork ��5

Leg Assembly  5
Attaching Tabletop  6
Assemble & Attach Treadle  7
Attach Idler Pulley  8
Preparing Workhorse

Motor 9

Tabletop Motor Attachment 10

Linkage Bar Installation 11
Install Oil Tray & Hinges   12
Install Sewing Machine & Cover Bracket   13
Securing the Balance Wheel  14
Installing Timing Belts   15
Installing Belt Covers  16
Changing Motor Rotation  17

Insert Thread Stand Posts   18
Install Light & Wire   18
Removing the Fabric Sample  19

Sew like a pro with Sailrite

For in-depth information on setup and

assembly of your Leatherwork Sewing

Machine, please reference our free video at

Sailrite�com/leatherwork-setup or search

#300525XHT at Sailritecom

Summary of Contents for Leatherwork 3008-00














Search results

Summary of Contents for Leatherwork 3008-00

Reviews:

Related manuals for Leatherwork 3008-00

Brands by name

Popular brands

Sailrite Leatherwork 3008-00, Assembly Instructions Manual

Search results

Summary of Contents for Leatherwork 3008-00

Reviews:

Related manuals for Leatherwork 3008-00

Brands by name

Popular brands