2-Sagemcom Internal Information - No outside communication without authorization from appropriate Management
This document and the information contained are th e property of Sagemcom
3000499645-01
Page 2
WM Installation Manual (EN) 1.0
METER CHARACTERISTICS
The product is a water meter intended to be installed to count volume of water passing through. It offers measurements
of different flow parameters, a CAT-
nection with centralization system, an optional BLE interface, an optional optical infrared interface and a push button.The
measurement data can be displayed on the front panel LCD or are also remotely available via optical, BLE or the radio.
Certification
The CE marking attests to the conformity of the product with the international technical regulations and harmonized Eu-
ropean standards that apply when the product is released on the market, in particular in accordance with the FCC, UL
and NSF.
Innovation,
This Class B digital apparatus complies with Canadian ICES- 003
This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.
This device complies with RSS-247 of the Innovation, Science and Economic Development Canada Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, inclu- ding interference that may cause undesired operation
IMPORTANT NOTE: Radiation Exposure Statement:
This equipment complies with radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 3
1
cm (
1
ft) between the device and
your body.
Meters overview
An overview of the product in its standard configuration is presented in the next figure
Button
The meter is equipped with one push button on the front panel. It is used to navigate through the different menus and
sub-screens. Long push to change the menu, short push to change to the next screen of the menu, double short push to
edit and validate change.
COMMUNICATION PORTS
All communication ports are protected and requires a proper identification to work.
In case of uninstalling the product from the water pipes and prior to send it by air transportation, unsure that you have
desactivated all the radio.
Bluetooth Low Energy PAN radio (if equipped)
If available on the product; a BLE radio, in the frequency band 2.4 - 2.483 GHz, could be used used to read and write
information into the applicative part of the meter.
Package and Thread-
ing Screw seal ring
Water Outlet
Water inlet
Water flow direction
Button
LCD display
Infrared interface
Metrology flashing LED
WAN radio antenna
External RF conn.
PAN BLE antenna
2-Sagemcom Internal Information - No outside communication without authorization from appropriate Management
This document and the information contained are th e property of Sagemcom
3000499645-01
Page 3
WM Installation Manual (EN) 1.0
Infrared communication port
An optical port compatible with IrPHY SIR 115.2kb/s could be available. This port can be used to read and write infor-
mation into the applicative part of the meter.
Remote CAT-M WAN radio (if equipped)
The Wide Area Network radio communication port is based on a LTE 4G Cat-M1 into the band 4 and 13.
Band
Uplink
Low Freq
(MHz)
Uplink
High Freq.
(MHz)
Downlink
Low Freq.
(MHz)
Downlink
high Freq.
(MHz)
Band widh
(MHz)
4
1710
1755
2110
2155
45
13
777
787
746
756
10
LCD DISPLAY
The meter LCD display symbols and meaning are depicted here after:
MOUNTING
The product must be installed in conformance with . It can be in-
stalled whatever the pipe orientation. The arrow on the product
pipe must be in the same direction than the normal water flow.
Upstream and backstream water lines must be aligned and must
have a connection distance compatible with the product pipe
length.
For proper mounting:
Press the rotating nut against the thread of the meter
Make one turn by unscrewing slowly to make sure the thread is
correctly engaged.
Then engage, screw the nut by hand and finish with a wrench (30
Nm max) without holding the main housing.
Due to the battery chemical, the garanteed product lifetime is not achieved when the product is:
With the pipe installed Horzontally and the SMA connector downward
1
2
3
To identify metrological in-
formation . When this sym-
bol is off, it depicts an in-
formative data from appli-
The right arrow defines
the normal flow direc-
tion water. The left ar-
row blink in case of re-
verse flow
Indicates that there
is air into the spool
piece or a leakage
possibility
Same as the one
on the left end. to
indicate each an
specific applica-
tion menu.
Displayed in
case of error
Indicates the
link quality
If this symbol is
OFF: the battery is
fully loaded.
Flow measure-
ment unit
Volume meas-
urement unit
