SAGEMCOM F5380, User Manual

Page: 3 / 4

SAFETY INSTRUCTIONS
Important Information about the Sagemcom
“FAST 5380” (CWR226e):
Important Information about the Sagemcom “FAST 5380” (CWR226e):
Installation and Safe Usage Instructions:
1. Place the router in a vertical orientation on a flat surface.
2. Connect the manufacturer supplied AC to DC power adapter. The FAST
5380 router requires the use of a 12VDC, 3.5A power adapter. Only use
a manufacturer supplied and approved power adapter and Ethernet
cable. Always first plug the mains adapter lead into the FAST 5380, then
the mains lead into the mains adapter, and finally the mains lead into the
mains socket. If you do not follow this order of connection, you may get
an electric shock. Make sure that the mains lead is properly inserted into
the power supply unit, and that it is correctly pushed into the recess. It
is very important to push the mains lead until the recess bottom. If it is
incorrectly connected this may cause a risk of fire or electric shock.
3.
Connect the “FAST 5380” to the AC Mains in accordance with the
installation instructions in this booklet, and the markings on the
identification label (voltage, current, and frequency of electricity network).
4. According to installation method required by your ISP:
- Connect the Ethernet cable (provided) to the RJ45 port labeled
“WAN”
on one end and to the Internet access device provided by your ISP on
the other end.
5. For connection of a computer with an Ethernet cable use one of the RJ45
ports on the product marked «1», «2». Then connect the other end of the
Ethernet Cable to the Ethernet port of a computer. Repeat as necessary
with the other available Ethernet ports.
6. Battery: Use to connect to the battery with USC Link cable provided by
dedicated battery vendor. This port only used to transmit the signal data.
The battery port is a signal transmitting port only and is not for supplying
power to the equipment.
When using this device, basic safety precautions should always be followed
to reduce the risk of fire, electric shock, and injury to persons including the
following:
1. Do not use this product near water and avoid contact with moisture. For
example, does not use near a bathtub, wash bowl, kitchen sink, laundry
tub, in a wet basement, or near a swimming pool. Care should be taken
so that liquids are not spilled on this equipment.
2. This equipment is for indoor use only, do not place or install in an outdoor
location.
3. Ethernet ports are intended to be connected to indoor cable circuits that
are exclusively located within the building where the product FAST 5380
is installed, and don’t terminate on a remote equipment earthed to a
different earthing network.
4. The devices connected to the telephone interfaces must be kept indoor
use only.
Caution: To reduce risk of electric shock, fire or damage to the
equipment, do not connect telephone or telecommunications
public network into
“PHONE” port.
5. Avoid using a telephone (other than a cordless type) during an electrical
storm. There may be a remote risk of electric shock from lightning.
6. Do not use the telephone to report a gas leak in the vicinity of the leak.
7. Make sure the power socket to which you connect the power cord is
easily accessible and as close as possible to the equipment so that the
appliance can be unplugged quickly in case of a problem.
8. Place your product on a firm, solid surface, no obstacle at a minimum
distance of 50cm (1.64feet). If you put it on something unsteady, it may
fall and be damaged. If you place it on a soft surface, such as rug, sofa
or cushion, the vents may be blocked, causing the product to overheat.
9. Never insert objects into the vents of this equipment as this can result in
the risk of electrical shock or fire.
10. As the power adapter is the only way to connect to the electrical network,
the product must be installed near an easily accessed power outlet.
11. This equipment should only be operated with the type of power supply
(Voltage and Current) indicated on the marking label.
12. Do not overload wall outlets or extension cords. Doing so can result in
the risk of fire or electrical shock.
13. Avoid blocking any vent openings or exhaust exits on this equipment. Do
not place equipment in a built-in installation such as a cabinet that may
impede the flow of air through the ventilation openings.
14. The equipment should be situated away from heat sources such as
radiators, heat registers, stoves, or other heat producing appliances and
equipment.
15. To disconnect this equipment from AC power, unplug the power supply
from the AC wall socket.
16. Care should be taken to ensure that the power cord is routed, so it is not
likely to be walked on or pinched by items placed upon or next to it.
17. Unplug this equipment before cleaning. Do not use liquid cleaners or
aerosol cleaners. Use a damp cloth for cleaning only.
18. This equipment is not user serviceable and is to be serviced by qualified
personnel only. Do not disassemble this equipment. If service is required,
disconnect all power from the equipment and consult qualified service
personnel.
19. To disconnect this equipment from AC power, unplug the power supply
from the AC wall socket.
20. Use the product in the environment specified as below:
- Air temperature between 0°C (32 F) and +45°C (113 F).
- Relative humidity between 5% and 95%.
- Altitude: 2743 meters (9000feet) maximum.
21. For RJ Cable(Telephone line cord)
- Caution: To reduce the risk of fire, use only 26AWG or larger
telecommunication line cord
Federal Communications Commission (FCC) Statements
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
Modifications:
You are cautioned that changes or modifications not expressly approved
by the party responsible for compliance could void your authority to operate
the equipment.
FCC Responsible Party: Sagemcom USA
14651 N. Dallas Parkway
Suite 900
Dallas, TX 75254
Phone: 972-674-4100
Radio Frequency Interference Statement
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
This device produces radio frequency energy in the 2.4GHz and 5GHz
spectrum. The antenna must be positioned to keep a minimum distance
of 50 cm (1.64 feet) from the radiating element to any nearby person.
North American Cable installer: This reminder is provided to call the your
attention to Section 820.93 of the National Electric Code (Section 54 of
the Canadian Electrical code, Part 1) which provides guidelines for proper
EN