Sage SE-Pre 1 Handbook Download Page 14

SE - Pre 1

ª microphone preamp

Some provinces / states do not allow the exclusion or limitation of incidental or

consequential damages, or length of time an implied warranty remains in effect.  As such,

the above exclusions may not apply.  This warranty gives you specific legal rights and you

may also have other rights which can vary from province to province ~ state to state.

Should your sage ELECTRONICS

¨

 product require service or repair please email us at:

[email protected]

 or call us at (613) 228-0449 ~ with the following information:

*

your name

*

your return shipping address

*

your telephone number(s)

*

your product's model number (example: SE-Pre1)

*

your product's serial number (located on side or rear of chassis)

*

date and location of purchase

*

description of problem or the service required

Upon sage ELECTRONICS¨' receipt of the above information from you we will provide you

with your return authorization number.  From this point we ask that you please;

¥

 

pack your unit carefully.

 Use your original packing if possible. If you do not have the

original packaging, make sure your unit has adequate protection. Tight thick bubble

wrap and foam is best if you do not have the original packing

¥

 

include a note in the box

 describing your problem or the service that your unit

requires. Be sure to 

include your return authorization number

 on this note

¥

 

write your return authorization number on the outside of your package / carton

packages without a return authorization number will be returned to sender

¥

 

Customer is responsible for paying shipping and insurance to sage

ELECTRONICS¨ facility.

  sage ELECTRONICS¨ will pay the return freight and

insurance via FEDEX ground or Canada Post.

end

Summary of Contents for SE-Pre 1















Reviews: