background image

16

ADVANCED CLEANING FOR THE CONICAL BURR GRINDER

Set ‘GRIND SIZE’ to ‘1’
(finest)

Use 10mm socket. Rotate
‘Clockwise’ to loosen the
nut only

Set ‘GRIND SIZE’ to ‘16’
(coarsest)

Unlock & remove top burr

Remove nut, spring & flat
washer. Carefully remove 
lower burr

Remove hopper

1

2

3

4

5

6

Clean chute with brush

Insert washers & grind fan
using long-nose pliers

Insert lower burr (drive pin
& cavity to align). Insert 
flat washer & spring washer 

Rotate ‘Counter-Clockwise’
to tighten nut

Unblock the grinds exit 
chute using the brush or
a pipe cleaner

8

9

10

11

12

Insert & lock top burr

13

Set ‘GRIND SIZE’ to ‘5’.
Replace & lock hopper

14

SINGLE

DOUBLE

PUSH TO GRIND

Remove grind fan & washers 
using long-nose pliers

7

POWER

FILTER SIZE

GRIND AMOUNT

GRIND SIZE

LOOSEN NUT

TIGHTEN NUT

GRIND SIZE

SPRING

WASHER

FLAT

WASHER

GRIND SIZE

1. GRIND FAN
2. METAL WASHER 
3. FELT WASHER 

3

2

1

1. FELT WASHER 
2. METAL WASHER 
3. GRIND FAN 

1

2

3

SPRING

WASHER

FLAT

WASHER

WARNING

 

Care should be taken as the grinder burrs are 

extremely sharp. 

This step is only required if there is a blockage between the grinding burrs and the grinder outlet. 

CLEANING THE STEAM WAND

The steam wand should always be cleaned after 

texturing milk. Wipe the steam wand with a damp 

cloth. Then with the steam wand tip directed over 

the drip tray, briefly set the STEAM / HOT WATER 

dial to the STEAM position. This will clear any 

remaining milk from inside the steam wand.
If any of the holes in the tip of the steam wand 

become blocked, ensure the STEAM / HOT 

WATER dial is in the STANDBY position. Press 

the POWER button to switch the machine off 

and allow to cool. Use the pin on the end of the 

provided cleaning tool to unblock the hole(s).
If the steam wand remains blocked, remove the  

tip using the integrated spanner in the cleaning 

tool and soak in hot water. Use the pin on the end 

of the provided cleaning tool to unblock the hole(s) 

before re-attaching to the steam wand. 

CLEANING THE FILTER BASKETS 

AND PORTAFILTER

The filter baskets and portafilter should be rinsed 

under hot water immediately after use to remove 

all residual coffee oils.

If any of the holes in the filter basket become 

blocked, use the pin on the end of the provided 

cleaning tool to unblock the hole(s).
If the hole(s) remain blocked, dissolve a cleaning 

tablet in hot water and soak filter basket and 

portafilter in solution for approx. 20 minutes.  

Rinse thoroughly.

CLEANING THE SHOWER SCREEN

The group head interior and shower screen 

should be wiped with a damp cloth to remove any 

ground coffee particles.
Periodically purge the machine. Place an empty 

filter basket and portfilter into the group head. 

Press and hold the 1 CUP button and run a short 

flow of water to rinse out any residual coffee. 

CLEANING THE DRIP & 

STORAGE TRAY

The drip tray should be removed, emptied and 

cleaned at regular intervals, particularly when the 

drip tray full indicator is showing EMPTY ME!
Remove the grid from the drip tray. Lift the coffee 

grind separator and dispose of any coffee 

grounds. The EMPTY ME! indicator can also be 

removed from the drip tray by pulling upwards 

to release the side latches. Wash all parts in 

warm soapy water with a soft cloth. Rinse and 

dry thoroughly. 

Summary of Contents for Barista Express SES875UK














Reviews: