background image

Specialized in developing,designing and manufacturing kinds of vinyl cutter

●Switch the cutting plotter on,when the cutting plotter is switched on, the
cutting plotter can be changed and modified as required.
●To change the zero point on,when the cutting plotter is switched on, the
carriage can be changed and modified as required.
●You can now adjust the zero point setting for your cutting plotter,first press
the On/Off key to toggle to Off mode.
●You can now adjust the zero point by pressing the four arrow keys..We
recommend setting the zero point to the front right corner of the media.While
the carriage moving,the current coordinates are display relative to the previous
zero point setting.
●Press Enter to confirm the new zero point setting .
The coordinates shown in the display are set to zero.

6.6 Setting Mode

You can press the mode key multiple times in off mode toggle through the
following menus:

Force

Use the Left/Right keys to set the force in unites of one gram ;the valid range
of values is between 0g and 750g(servo) or 0g and 510g (stepper),2g/step.

When setting the cutting force ,please note that the correct setting mainly

depends on the blade holder, the position of the blade ,and the loaded
media.These settings are subject to variation.

Before work you can press the

test button to test.

Speed

Again use the UP/Down keys on the operating panel to set the speed.

X-Scale/Y-Scale
Don’t change the X-Scale or Y-Scale values as they are used to compensate
for wear and tear of the transport belts.Only change these settings,if plots
come distorted.

Baud Rate

The Baud Rate is the communication speed for the cutting plotter and the
serial port on your computer.This setting must reflect the baud rate set in the
properties dialog for your COM port.Or in the software Value of 38400 are
typically set.

Summary of Contents for SAGA-1350I



















Reviews: