SafeWaze LATITUDE HD SRL-P Instruction Manual Download Page 14

Page: 14 / 20

Page 14

FIGURE 8 - SW-9012 BWB INSTALLATION

FIGURE 9 - 9013 BWB INSTALLATION

FIGURE 10 - FS1014-TL-BLACK-BWB INSTALLATION

Curved Portion

of SW-9012

Bar assembly of bracket which inserts

behind webbing at dorsal D-ring

Locking Button (B)

Locking Button (A)

LOAD IN

DICATO

LOA

D IN

DIC

ATO

FALL-ARREST

ANSI Z359.14, ANSI A10.32

OSHA 1910.66, OSHA 1926.502

020053

ANSI Z359.14,

ANSI A10.32

OSHA 1910.66,

OSHA 1926.50

020053

Diagram of SW-9012 in opened

configuration

The SW-9012 Behind the Web Bracket (BWB) comes fully assembled and ready for installation. No tools are required for installation of the BWB onto a Full Body

Harness (FBH) harness. Use the following instructions and Figure 8 to install the 9012 BWB.

Connect To Harness:

Ensure that the curved portion of BWB is in a downward orientation relative to the harness (See Step 1).

Simultaneously depress both locking buttons (A) and (B) and slide the bracket open as indicated (See Steps 2 and 3)

With the bracket open, position the bar assembly in an orientation that will allow the bar to slide under/behind both web loops at the Dorsal Dring of

the FBH.

4. While pressing in on locking button (A) slide the bar behind both loops of webbing at dorsal D-ring until the bar locks back into place (See Step 4).

Check the locking function of the bracket by attempting to slide the bracket open WITHOUT depressing locking buttons (A) or (B). Bracket

bar should not move and the bracket is now locked into place.

The 9013 brackets comes fully assembled and ready for installation. No tools are required for installation of the bracket onto harness. Use the following

instructions and Figure 9 to install the 9013 Behind the Web Bracket.

Connect To Harness:

1. Ensure that the curved portion of 9013 is in a downward orientation relative to the harness (See Dwg. 1).

2. Simultaneously depress both locking button (A) and and slide lock (B) (See Dwg. 2) to swing the bracket open as indicated (See Dwg. 3).

3. With the bracket open, install dual leg retractables onto the bracket via the swivel tops of each. Swivels should be hanging on the curved

portion of bracket.

4. Slide the bar behind both loops of webbing at dorsal D-ring. Swing the bracket closed unti it locks into place.

5. Check the locking function of the bracket by attempting to swing the bracket open WITHOUT depressing locking button (A) or

slide lock (B). Bracket bar should not move and the bracket is now locked into place.

6. Dual leg Retractables can be easily installed and removed from bracket by once again depressing both locking button (A) and

slide lock (B), which allows bracket to swing open without complete removal from harness.

The behind the web bracket comes fully assembled and ready for installation. No tools are required for installation of the bracket onto harness. Use the following

instructions and Figure 10 to install the bracket:

Connect to Harness:

1. Unfasten the two small brackets on the green retractable spacer off of the carabiner.

2. Slide the green spacer around to the side of carabiner to allow opening of the carabiner gate.

3. Open the carabiner gate and slide spacer off of carabiner and remove one of the retractables.

4. Holding gate open on carabiner, insert the open end of carabiner through the webbing loops at the Dorsal D-ring of the harness.

Ensure that both loops of webbing on are captured inside of carabiner.

5. With carabiner gate still open, slide the removed retractable and green spacer back onto carabiner and allow carabiner gate to close.

6. Slide the green retractable spacer back over the gate of carabiner and snap the two small brackets back into place on carabiner, with the

web loops positioned between the ends of the bracket.

LOAD IN

DICATO