V1.1 2019 Copyright SAFEWAZE™
V1.1 2019 Copyright SAFEWAZE™
Page 12
7.0 MATERIALS
TABLE 6 - MATERIALS
Ultra High Molecular Weight Webbing
Carbon Steel
SW-9012 Behind Web Bracket
Housing
Drum
Fasteners
Main Shaft
Web
Motor Spring
Plastic with Stainless Steel Rivets
FS1014 Behind Web Bracket
Aluminum Alloy
Zinc Plated Alloy Steel Screws
Stainless Steel
Steel Alloy, Plastic Retaining Clip
Forged Steel
Forged Steel Gate, Aluminum Barrel
Carbon Steel
Forged Steel or Aluminum
Polyester
9013 Behind Web Bracket
Swivel
Snap Hook / Rebar Hook
Web Label Cover
8.1 BEFORE EACH USE
Before each use ensure that the equipment is in good working condition. Inspect the unit to ensure it has not been
damaged and that the unit pays out and retracts properly. Prior to each use, the braking system must be inspected. Grasp
the body of the unit in one hand and the cable/web in the other. With a quick, jerking motion, pull down on the web. The
brake should engage, stopping movement almost immediately. Inspect the webbing using the “Inspection Checklist”
located on page 15 of this manual, and ensure that all connection hardware is working properly. Brake
failure or unsatisfactory results during any portion of the inspection, require immediate removal of the SRL from service.
8.0 INSPECTION
8.3 UNSAFE OR DEFECTIVE CONDITIONS
Figure 10 shows examples of equipment damage. Equipment inspectors must be trained to look for damage to
components indicated in Figure 9, as well as other damage that may occur. If inspection reveals an unsafe or defective
condition remove the SRL from service.
8.5 DISPOSAL
Dispose of the SAFEWAZE™ 019-5000 series SRL if it has been damaged by fall arrest forces or inspection reveals an
unsafe or defective condition that cannot be repaired by an authorized SAFEWAZE™ Service Center. Before disposing of
the SRL, cut the web lifeline in half so that it is not mistakenly reused.
8.4 PRODUCT LIFE
The working life of SAFEWAZE™ SRL’s is determined by work conditions, care and inspection processes. As long as the
SRL passes inspection, it may remain in service.
9.0 LABELING
FIGURE 8 - LABEL EXAMPLES
WWW.SAFEWAZE.COM
Ø 59.5mm
SELF RETRACTING LANYARD
SELF RETRACTING LANYARD
ANSI Z359.14 & ANSI A10.32
OSHA 1910.66 & OSHA 1926.502
Inv #: 02008a7R2
Fall Arrest Systems
•
Confined Space
•
Engineering
•
Rescue Systems
6’
6’
SPECIFICATIONS: Working length: 6 ft (1.83 m)
Materials: Steel hardware, Plastic housing, and UHMWPE webbing
Capacity: ANSI 130-310 lbs (58.97-140.61 kg), OSHA up to 420 lbs (190.51 kg)
Class B Unit
Average arresting force: 900 lbs (408.2 kg); Max arrest force: 1800 lbs (816.47 kg);
Max arresting distance: 54 in (137.16 cm)
MODEL# 019-5040 I 6 FT WEB SELF RETRACTING LANYARD WITH STEEL SNAP HOOK
SERIAL #: XXXXXXX MFG DATE: XX/XXXX
MUST FOLLOW ALL MANUFACTURER’S INSTRUCTIONS INCLUDED WITH THIS EQUIPMENT. DO NOT REMOVE LABEL.
322 Industrial Court
Concord, NC 28025
(800) 230-0319
www.safewaze.com
019-5040
01385b
SPECIFICATIONS: Working length: 6 ft (1.83 m)
Materials: Aluminum hardware, Plastic housing, and UHMWPE webbing
Capacity: ANSI 130-310 lbs (58.97-140.61 kg), OSHA up to 420 lbs (190.51 kg)
Class B Unit:
Average arresting force: 900 lbs (408.2 kg); Max arrest force: 1800 lbs (816.47 kg);
Max arresting distance: 54 in (137.16 cm)
MODEL# 019-5055 I 6 FT WEB DUAL LEG SELF RETRACTING LANYARD WITH ALUMINUM REBAR HOOKS
SERIAL #: XXXXXXX MFG DATE: XX/XXXX
MUST FOLLOW ALL MANUFACTURER’S INSTRUCTIONS INCLUDED WITH THIS EQUIPMENT. DO NOT REMOVE LABEL.
322 Industrial Court
Concord, NC 28025
(800) 230-0319
www.safewaze.com
019-5055
01385s
J
D
N
O
S
A
J
J
M
A
M
F
8.2 INSPECTION FREQUENCY
SAFEWAZE™ 019-5000 series SRL’s - must be inspected at the intervals defined in section 2.3. Inspection procedures
are described in the “Inspection Checklist” (See page 15).
Ø 59.5mm
Inv #: 02008b7R4
MUST FOLLOW ALL MANUFACTURER’S INSTRUCTIONS
INCLUDED WITH THIS EQUIPMENT. DO NOT REMOVE LABEL.
WARNING
: User must read and understand all instructions,
provided with this product at time of shipment, prior to use.
DO NOT ATTEMPT TO SERVICE OR REPAIR THIS UNIT!
CONTACT SAFEWAZE™ FOR SERVICE OR REPAIR INFORMATION.
INSPECTION:
Device must be inspected prior to each use. Inspect
device per instructions to include Locking Function Test (sharp pull test),
retraction test, label legibility, any evidence of damage or defects, or
missing components or parts. Inspect housing, connectors, fasteners
and full length of lifeline component for any damage or defects. This
product must be inspected in accordance with the manufacturer’s
instructions. Unit must be removed from service if exposed to fall
arrest forces. Fall indicator is sewn into webbing above the
snap hook; immediately remove unit from service if the fall
indicator is visible.
