background image

6

47 SERIES IP CAMERA

Camera Mounting

Use the following procedure to install the 47 series camera:

1. 

Clean the area where the camera is to be installed.

2. 

Mark mounting and cable exit hole locations. 

Use the included adhesive template and mark the four mounting screw holes 
and cable exit hole in the desired mounting location.

3. 

Drill cable exit hole. 

Use a hole saw or appropriate drill bit to drill a .8 inch hole for the cable exit, 
as shown on the template.

4. 

Drill anchor holes 

(optional)

If using the included anchors, use an appropriate drill bit to drill four screw 
holes where marked.

5. 

Remove camera dome cover. 

Using a T15 TORX™, loosen the 2 locking screws and remove  
dome cover.

6. 

Secure camera to mounting surface. 

Thread the cable through the hole and secure the camera base to the 
mounting surface using the included 4 self-tapping screws.  

7. 

Connect 47 series camera to NVR. 

Connect the 47 series camera to one of the camera inputs on the NVR.

8. 

Configure 47 series camera. 

Using a laptop, access the camera’s live view as described in the  
Configuration 

section.

9. 

Adjust camera angle and field of view. 

Use a small Phillips head screwdriver (pan rotation) and a T15 TORX (tilt 
rotation) to loosen the screws on the camera gimbal to adjust the camera 
angle to the desired field of view.  Once completed, tighten the screws in 
place.

10. 

Secure camera dome cover. 

Using a T15 TORX™, tighten the 2 locking screws and secure the dome cover 
over the camera and base. 

Summary of Contents for 47 SERIES





















Reviews: