FCC Statement:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
*
Reorient or relocate the receiving antenna.
*
Increase the separation between the equipment and receiver.
*
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Note: Modifications to this product will void the user's authority to operate this equipment.
Insert the cable duct to the base
Place the wires in the cable duct
and
replace the cable duct cover
+
+
+
Black Color
Red Color
(Front Door)
White Color
(Back Door)
CODE PAIRING & MELODY SELECTION
Step 1:
Insert battery to the transmitter to be used.
Step 2:
Insert batteries to the receiver to be used
(chime unit).
Step 3:
Enter pairing mode for receiver (chime unit).
Press and hold
the • zone selector button for 3 seconds
until the "zone 1" led light is blinking.
Step 4:
If you are programming zone 1, move to next
step. To program to a different zone, scroll to another
zone by pressing the • zone selector until you reach the
desired zone.
F
Frro
on
nt D
t Do
oo
or
Bu
utttto
on
n
Back Door
Button
W
ARNING:
Cancer and Reproductive Harm. Go to
www.P65Warnings.ca.gov
for
more information.
TEST THE TRANSMITTER
To test the transmitter, press the test button of the front door or back door once. the LED
indicator will lit and will send a trigger signal to the receiver.
TEST THE CONNECTION
To test the connection between the transmitter and Doorbell, press the Door bell button. the
LED indicator on the transmitter will lit and will send a trigger signal to the receiver.
DELETE A TRANSMITTER FROM A ZONE ON RECEIVER
First, Press and hold the 'Zone selector' • button for 3 seconds to enter the programming
mode. Press the 'Zone selector' button • to scroll the zone you want to delete. Press and
hold both the 'Zone selector' • button and the 'Melody' button ♫ for approximately 5
seconds. The chime will generate a tone to indicate the remote on this zone has been
deleted.
CHANGING THE MEDLODY FOR A ZONE
First, Press and hold the 'Zone selector' button • for 3 seconds to enter programming mode.
Press the 'Zone selector' button • to scroll to the zone you want to change. Press the
'Melody' ♫ button to select the new melody/tone and then push button on the transmitter.
You will hear a tone to indicate the melody has been changed.
BATTERY LOW INDICATOR
If a zone LED light is blinking, it indicates that the battery is low for this transmitter. You
must replace the battery as soon as possible. If the white flash at the top of the Chime
blinks every 5 seconds, this indicates the receiver batteries are low. You must replace the
batteries of the receiver .
TECHNICAL SUPPORT
If you need assistance with the operation of this product, please contact us. You can reach
us by phone at 904-245-1184 from 8:00AM to 5:00PM Monday through Friday, EST. You
may also reach us via email at [email protected].
WARRANTY INFORMATION
The product you have purchased is guaranteed against defects in workmanship and
materials for a period of one year from the date of purchase. Warranties implied by law are
subject to the same time period limitation. For a detailed warranty policy, please visit our
website by visiting: www.safeguardsupply.com
Mount the Wireless Chime Extender beside the wired doorbell. Connect the
wires as indication (The wiring of doorbells may be different between
manufacturers, please refer to the manual).
•
Red Wire - Front Door on Wired
Doorbell
•
White Wire - Back Door on Wired
Doorbell
•
Black Wire - Common on Wired
Doorbell
LRA-EXTX WIRE SETUP
Step 5:
Choose the desired melody for the zone by pressing the melody selector ♫
button until you hear the melody you want to use for that zone.
Step 6:
Now that the desired zone & melody are selected, press the "front door"
button on the LRA-EXTX transmitter.
Step 7:
If your wired doorbell supports a back door button and you would like to
program it, repeat
steps 4-6.
For example, scroll to zone 2, select a different
melody, and press the "back door" button on the LRA-EXTX
to program the back
door
.
Note
: if you do not have a second door, simply wrap the white wire
connector in electrician's tape.
