a eguar u ly
oon tation t.
ennesaw, A
www.safeguardsupply.com
Test the rogra
ing
After completing the programming steps abo
v
e, test the
programming pairing prior to mounting the transmitter.
Trigger
the transmitter/sensor. The receiver should play the melody,
flash, or do both, depending on mode of operation.
Lo attery In i ator
A randomly blinking one light on the A
A-L recei er
indicates that the battery is low for this transmitter. lease
replace the battery as soon as possible.
When batteries are low in the receiver, the strobe light will
flash once every 5-seconds.
TE
I AL
RT
If you encounter any difficulty in the operation of this product after
reading the manual, please contact us. You can reach us by phone at
from
A Ā
to
M
onday
-F
riday
(
astern
S
tandard
Time . e will
be happy to answer your
questions
and help you
in any way
we can.
WARRANTY
: The product you have purchased is guaranteed against defects
in workmanship and materials for a period of one year from the date of
purchase. Warranties implied by law are subject to the same time period
limitation. For a detailed warranty policy, please visit our website by visiting:
www.safeguardsupply.com
AR I
ancer and eproducti e arm. o to
www.P65Warnings.ca.gov
for more information.
rogra
ing the
Receiver (
ont
•
W
hen the transmitter has
successfully
paired to the
recei er,
the
strobe on the
receiver
will flash once, and the
next
one s
will
start blinking
(showing that zone is now
in program mode).
•
If you would like to program another transmitter/sensor,
follow this
step
continue the above steps.
If not, skip to the next step.
•
Using the zone selector button, scroll past zone 4. This will cause
the receiver to exit programming mode.
Changing the Melody for a Zone
•
Press & hold the zone selector button until the zone indicator light
begins to blink (approximately 3-seconds). Release the button.
•
Press the zone selector button to select the specific zone for melody
change. Once you arrive on that zone, stop pressing the button.
•
Next, press the melody button to scroll through the available
melodies.
•
Trigger the transmitter programmed to this zone. You will then hear
a short tone sound indicating the melody has been changed.
Deleting a Transmitter/Sensor from Zone Memory
•
Press & hold the zone selector button until the zone indicator light
begins to blink (approximately 3-seconds). Release the button.
•
Press the zone selector button to select the specific zone for
melody change. Once you arrive on that zone, stop pressing the
button.
•
Simultaneously, press & hold both the zone selector & melody
buttons for approximately 5-seconds.
•
The receiver will play a short tone sound indicating the memory
has been deleted.
Using Relays On Back of Receiver
Cancel
Output
delay
Wire Clip
Relay
Output
control
5
2
On
Off
Using Relays On Back of Receiver (cont.)
The receiver features
a normally open & normally closed
relay on
back of the receiver (see image). This relay may be used to
integrate the receiver with other devices that accept a relay.
Please note: the relay only works for zone 4 on the receiver. For
example, if you want to use the "normally closed" relay, ensure a
transmitter/sensor that triggers the relay is programmed to zone 4.
•
Slide the switch to the "On" position. This will activate the relay when
zone 4 is triggered. Sliding the switch to the "Off" position will not
activate the relay when zone 4 is triggered.
•
Slide the switch to the 2' position & the relay will activate for 2 seconds,
5' is 5 seconds.
•
The relay
s on back of the receiver will open or close only. It does not
supply external power. The integrated device must supply power for it
to activate.
Or
LRA-DCRX MOUNTING OPTIONS
Wall moun
t
Sits on
desk Top
25mm
o
/ 7mm
