SAF-HOLLAND DB-1250-3 Owner'S Manual Download Page 12

From fifth wheel rebuild kits to suspension bushing repair 

kits, SAF-HOLLAND Original Parts are the same quality 

components used in the original component assembly. 

SAF-HOLLAND Original Parts are tested and designed to 

provide maximum performance and durability. Will-fits, 

look-alikes or, worse yet, counterfeit parts will only limit 

the performance potential and could possibly void  

SAF-HOLLAND’s warranty. Always be sure to spec  

SAF-HOLLAND Original Parts when servicing your 

 SAF-HOLLAND product.

SAF-HOLLAND USA, INC.
1950 Industrial Blvd., Muskegon, MI 49443
www.safholland.com

XL-DB20015UM-en-US Rev – · 2015-07-29 · 

Amendments and Errors Reserved · © SAF-HOLLAND

, Inc.,

 SAF-HOLLAND

, HOLLAND

, SAF

, and logos are tr

ademarks of SAF-HOLLAND S

.A.,

 SAF-HOLLAND GmbH,

 and SAF-HOLLAND

, Inc.

SAF-HOLLAND USA

 

· 

888.396.6501 

· 

Fax  800.356.3929

www.safholland.us

SAF-HOLLAND CANADA

 

· 

519.537.3494

 

· 

Fax

  

800.565.7753

      

WESTERN CANADA

 

· 

604.574.7491

 

· 

Fax  604.574.0244

www.safholland.ca

SAF-HOLLAND MEXICO

 

· 

52.1.55.5456.8641

 

· 

Fax  52.55.58162230

www.safholland.com.mx

[email protected]

Summary of Contents for DB-1250-3













Reviews: