background image

 

WARRANTY 

 

ROTO-PRESS warrants to the initial purchaser of a new ROTO-PRESS product from an authorized 
ROTO-PRESS dealer that the product and the components thereof manufactured by ROTO-PRESS are 
free from defects in material and workmanship at the time of shipment.  ROTO-PRESS further 
warrants to such purchaser that each new ROTO-PRESS product will perform without structural or 
operational failure if the product is assembled and mounted in accordance with ROTO-PRESS's 
instruction and drawing and is then operated and maintained as described in the Owner's Manual. 

 

WARRANTY PERIOD

 

The above warranty shall be effective for a period of one year on workmanship and materials from the 
date of delivery by the ROTO-PRESS dealer to the initial purchaser. 
 

PURCHASER'S REMEDIES 

If a warranted ROTO-PRESS product or component fails to conform to the above warranty during the 
one year warranty period, ROTO-PRESS will furnish the parts, and labor at the factory necessary to 
correct such failure, provided ROTO-PRESS is notified through the selling representative within 30 
days of the discovery of the failure.  All warranty submissions must include the original part in 
question, along with a properly filled out warranty claim sheet, before a warranty award will be made.  
Labor at the factory is specified as labor done at the ROTO-PRESS factory ONLY!  ROTO-PRESS 
will pay the common carrier freight expense of parts to and from the owner.  Faster freight service is 
available, with the owner paying the difference in cost between common carrier and preferred method 
by owner.  Freight of whole goods to or from the factory is the owner’s expense, regardless if they fall 
under warranty or not.  All warranty decisions will be final! 
 

EXCLUSIONS 

This warranty shall not apply to component parts or accessories of products not manufactured by 
ROTO-PRESS and which carry the warranty of the manufacturer thereof.  Items of high wear and 
regular maintenance shall not be covered under this warranty.  This warranty shall be void if any part 
or parts not manufactured by ROTO-PRESS are used either in maintaining or servicing of the products 
covered by  this warranty.  No warranty whatsoever is made on used, secondhand, altered, or rebuilt 
machinery. 
 
 

THIS WARRANTY IS EXTENDED TO THE INITIAL PURCHASER FROM AN 
AUTHORIZED ROTO-PRESS DEALER AND MAY NOT BE ASSIGNED.  THIS 
WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER WARRANTIES EXPRESSED OR 
IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FOR 
A PARTICULAR PURPOSE AND ROTO-PRESS NEITHER ASSUMES NOR AUTHORIZES 
ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY.  THERE ARE NO 
WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE 
THEREOF. 

 

We reserve the right to make improvements to any of our products without notice of obligation 
regarding models previously sold. 

Summary of Contents for ROTO-PRESS 904












































Reviews: