SABINE True Mobility SWM1600 Operating Manual Download Page 38

38

Section Twelve:  Cautions and Warranties

Warning! This equipment must be earthed.
Caution! Risk of electric shock. Do not open.
Caution! Shock hazard. Do not remove covers. No user serviceable parts
inside. Refer servicing to qualified service personnel.
Warning! To reduce the risk of fire or electric shock, do not expose this product
to rain or moisture.

Attention! Cet appareil doit être relié à la terre.
Attention! Risque de choc électrique; ne pas ouvrir.
Attention! Risque de choc; ne pas oter les capots. Aucune pièce accessible à
l'intérieur. S'addresser à un technicien qualifié.
Attention! Pour réduire le risque d'incendie ou de choc électrique, ne pas laisser
l'appareil sous la plouie ou à l'humidité.

Achtung! Dieses Gerät muss schutzgeerdet sein.
Achtung! Gefar eines elektrischen Stormschlags. Gehause nicht öffnen.
Achtung! Gefar eines elektrischen Stormschlags. Gehäuse nicht öffnen. Keine
con Benutzer zu bedienenden Teile im Geräteinneren.
Überlassen Sie das Gerät zu Servicezwecken nur geschultem Fachpersonal.
Um Brandgefar oder das Risiko eines elektrischen Schlags auszuschließen,
das Gerät vor Nässe und Feuchtigkeit schützen.

Advertencia! Este equipo debe estar conectado a tierra.
Precaución! Reisgo de descarga eléctrica. No abrir.
Precaución! Riesgo de descarga eléctrica. No desmontar las tapas. Piezas
interiores no reparables por el usuario. Reparable sólo por personal cualificado.
Advertencia! Para reducir el riesgo de incendio o de descarga eléctrica no
exponga este producto a la lluvia o humedad.

FCC Statement:
This device complies with Part 15, Class B, of the FCC Rules.  Operation is
subject to the following conditions: (1) This device may not cause harmful
interference; and (2) This device must accept any interference received, in-
cluding interference that may cause undesired operation.  

Warning: 

Changes

or modifications to this unit not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules.  These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.  This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communications.  However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television recep-
tion, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.

Consult the dealer or an experienced radio TV technician for help.

Canadian Compliance Statement
This digital apparatus does not exceed the Class B limits for radio noise emis-
sions from digital apparatus set out in the Radio Interference Regulations of the
Canadian Department of Communications.
Le present appareil numerique n'emet pas de bruits radioelectriques depassant
les limites applicables aux appareils numeriques de la class B prescrites dans
le Reglement sur le brouillage radioelectrique edicte par le ministere des Commu-
nications du Canada.

Japanese EMI  Compliance Statement

SECTION TWELVE : CAUTIONS & WARRANTY

The True Mobility is designed to operate from standard AC
power.    Please be sure the power in your area is compatible
with the power requirements marked on the rear of the unit.
Using the wrong input voltage may cause permanent damage to
the unit and will void the warranty.

The True Mobility Wireless Microphone system is supplied
with one of the following AC power cords:
Japan

100 VAC

U.S./North America

120 VAC

Continental Europe

230 VAC

United Kingdom

240 VAC

Australia

240 VAC

Warning!

1. Read all safety and operating instructions before using this

product.

2. All safety and operating instructions should be retained for

future reference.

3. Obey all cautions in the operating instructions and on the

unit.

4. All operating instructions should be followed.
5. Use only shielded audio and data cables.
6. This product should not be used in the presence of moisture

or rain, or near any water, i.e., a bathtub, sink, swimming pool, wet
basement, etc.

7. This product should be located so that its position does not

interfere with proper ventilation. Do not use in direct
sunlight.  Do not place flat against a wall or in a built-in enclosure
that will impede the flow of cooling air.

8. This product should not be placed near a source of heat such as

a stove or radiator.

9. Connect only to a power supply of the type marked on the unit

adjacent to the power entry module.

10.Never break off the ground pin on the power supply cord.
11. Power supply cords should always be handled carefully.

Never walk or place equipment on power supply cords.
Periodically check cords for cuts or signs of stress, especially at
the plug and the point where the cord exits the unit.

12.The power supply cord should be unplugged when the unit

is to be unused for long periods of time.

13.Care should be taken so that objects do not fall and liquids

are not spilled into the unit through the ventilation holes or
any other openings.

14.This unit should be checked by a qualified service technician if:

A. The power supply cord or plug has been damaged.
B. Anything has fallen or been spilled into the unit.
C. The unit does not operate correctly.
D. The unit has been dropped or the enclosure damaged.

15.The user should not attempt to service this equipment. All

service work should be done by a qualified service technician.

Battery Caution!

MUST BE RECYCLED OR
DISPOSED OF PROPERLY

DO NOT BURN OR PUNCTURE BATTERY.
DOING SO COULD RELEASE TOXIC MATE-
RIALS WHICH COULD CAUSE INJURY. DO
NOT SHORT CIRCUIT

Summary of Contents for True Mobility SWM1600









































Reviews: