Saber Compact R50CC0612, Product Manual

Page: 7 / 60

·
Safety Tips
·
Before opening LP cylinder valve, check the coupling nut for
tightness.
·
When grill is not in use, turn off all control knobs and LP
cylinder valve.
·
Never move grill while in operation or still hot.
·
Use long handled barbecue utensils and oven mitts to avoid
burns and splatters.
·
Maximum load for sideburner and side shelf is 10 lbs.
·
The grease tray
must
be inserted into grill and emptied after
each use. Do not remove grease tray until grill has
completely cooled.
·
Clean grill often, preferably after each cookout. If a bristle
brush is used to clean any of the grill cooking surfaces,
ensure no loose bristles remain on cooking surfaces prior to
grilling. It is not recommended to clean cooking surfaces
while grill is hot.
·
If you notice grease or other hot material dripping from grill
onto valve, hose or regulator, turn off gas supply at once.
Determine the cause, correct it, then clean and inspect valve,
hose and regulator before continuing. Perform a leak test.
·
Keep ventilation openings in cylinder enclosure (grill cart)
free and clear of debris.
·
Do not store objects or materials inside the grill cart
enclosure that would block the flow of combustion air to the
underside of either the control panel or the firebox bowl.
·
The regulator may make a humming or whistling noise during
operation. This will not affect safety or use of grill.
·
If you have a grill problem see the
“Troubleshooting Section”.
·
If the regulator frosts, turn off grill and LP cylinder valve
immediately. This indicates a problem with the cylinder and
it should not be used on any product. Return to supplier!
Main Burner Ignitor Lighting
Do not lean over grill while lighting.
1. Turn
OFF
all control knobs.
2. Turn
ON
gas at LP cylinder.
3.
Open lid during lighting
.
4. To ignite, push and turn burner control knob to
HI
.
5. Push and hold
ELECTRONIC IGNITION
button until the burner
lights (use flame viewing ports to verify).
6. If ignition does
NOT
occur in 5 seconds, turn the control knobs
OFF
, wait 5 minutes, and repeat the lighting procedure.
7. Ignite remaining burners by repeating steps 4 through 6 for
each burner.
8. Once each burner has ignited, turn control knobs to desired
setting.
7
CAUTION
If ignition does NOT occur in 5 seconds, turn the
control knobs OFF, wait 5 minutes and repeat the
lighting procedure. If the burner does not ignite with
the valve open, gas will continue to flow out of the
burner and could accidently ignite with risk of injury.
Main Burner Match-Lighting
Do not lean over grill while lighting.
1.
Open lid
. Turn
ON
gas at LP cylinder.
2. Place match into match holder (hanging from left side of
cabinet). Light match; then light burner by placing match
through the match light hole on left side of grill.
3. Push in and turn left control knob to the
HI
position. Once
burner has ignited (use flame viewing port to verify) turn
control knob to desired setting.
4. If ignition does not occur in 5 seconds, turn the burner control
knob
OFF
, wait 5 minutes, and repeat the lighting procedure.
5. Light adjacent burners in sequence by pushing control knobs
in and turning to the
HI
position.
Burner Flame Check
·
Remove cooking grates and emitters. Light burners, rotate
knobs from
HI
to
LO
. You should see a smaller flame in
LO
position than seen on
HI
. Perform burner flame check on side
burner, also. Always check flame prior to each use. If only low
flame is seen refer to “Sudden drop or low flame” in the
Troubleshooting Section.
Turning Grill Off
·
Turn all control knobs to
OFF
position. Turn LP cylinder
OFF
by
turning hand-wheel clockwise to a full stop.
Ignitor Check
·
Turn Gas OFF at LP cylinder
. Press and hold electronic
ignition button. “Click” should be heard and spark seen each
time between collector box or burner and electrode. See
“Troubleshooting”
if no click or spark
.
HI
LO
Viewing ports