SAB KR 175 Drake Antartica Manual Download Page 4

IMPORTANT NOTES

*This radio controlled airplane is not a toy.

*This radio controlled airplane can be very dangerous.

*This radio controlled airplane is a technically complex device which has to be built and handled very carefully.

*This radio controlled airplane must be built following these instructions. This manual provides the necessary information to correctly 

   assemble the model. It is necessary to carefully follow all the instructions.

*Inexperienced pilots must be monitored by expert pilots.

*All operators must wear safety glasses and take appropriate safety precautions.

*A radio controlled airplane must only be used in open spaces without obstacles, and far enough from people to minimize the possibility of accidents or of injury to property or persons.

*A radio controlled airplane can behave in an unexpected manner, causing loss of control of the model, making it very dangerous.

*Lack of care with assembly or maintenance can result in an unreliable and dangerous model.

 

*Neither SAB Avio nor its agents have any control over the assembly, maintenance and use of this product. Therefore, no responsibility can be traced back to the 

  manufacturer. You hereby agree to release SAB Avio from any responsibility or liability arising from the use of this product.

 

 

SAFETY GUIDELINES

*Fly only in areas dedicated to the use of model.

*Follow all control procedures for the radio frequency system.

*It is necessary that you know your radio system well. Check all functions of the transmitter before every flight.

*The turbine of the model is very dangerous, be aware of the danger they pose and the damage they may cause.

*Never fly in the vicinity of other people.

 

DAMAGE LIMITS

SAB AVIO SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCT, 

WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. 

Further, in no event shall the liability of SAB Avio exceed the individual price of the Product on which liability is asserted. As SAB Avio has no control over use, setup, final assembly, modification or 

misuse, no liability shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly the user accepts all resulting liability. If you as the Purchaser or user are 

not prepared to accept the liability associated with the use of this Product, you are advised to return this Product immediately in new and unused condition to the place of purchase.

 

LIMITED WARRANTY

SAB Avio reserves the right to change or modify this warranty without notice and disclaims all other warranties, express or implied.

(a) 

This warranty is limited to the original Purchaser (“Purchaser”) and is not transferable. REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER This 

warranty covers only those Products purchased from an authorized SAB Avio dealer. Third party transactions are not covered by this warranty. Proof of purchase is required for warranty claims.

(b) 

Limitations- SAB AVIO MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NONIFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE 

PRODUCT. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.

(c) 

Purchaser Remedy- SAB Avio’s sole obligation hereunder shall be that SAB Avio will, at its option, replace any Product determined by SAB Avio to be defective In the event of a defect, this is the 

Purchaser’s exclusive remedy. Replacement decisions are at the sole discretion of SAB Avio. This warranty does not cover cosmetic damage or damage due to acts of God, accident, misuse, abuse, 

negligence, commercial use, or modification of or to any part of the Product. This warranty does not cover damage due to improper installation, operation, maintenance or attempted repair by 

anyone

Page 2

IMPORTANT NOTE

Summary of Contents for KR 175 Drake Antartica













































Reviews: