S9 Antennas S9v Installation Manual Download Page 19 | Manualshive

Page: 19 / 19

background image

S9v 43’ Installation Guide

___________________________________________________________________________

________________________________________________________________________

19

MAINTENANCE

The  S9v requires little,  if any,  maintenance.   The  S9v is finished with a durable
painted surface, but it is subject  to oxidation  – just  like an aluminum  antenna.   If
you  notice oxidation  (color becomes lighter),  use a soft cloth  and Armor All

TM

to

restore the  finish.   Automotive  spray  wax  is also an excellent  product to seal and
protect the  finish.   The  antenna  may  also be repainted, if desired, using a quality
exterior spray paint such  as Krylon

TM

or Rustoleum

TM

.

SUPPORT

If you have any questions or problems installing your S9v, please contact us.

You can reach us via:
Email -

[email protected]

Phone - 410-586-2177.
Web – www.ldgelectronics.com

Our mailing address is:

LDG Electronics
1445 Parran Road
St. Leonard MD 20685

«
...
17
18
19

Summary of Contents for S9v




















Reviews:

No comments

Related manuals for S9v

Brand: Cambium Networks Pages: 3

Brand: Adeunis RF Pages: 7

Brand: Camos Pages: 75

Brand: l-com Pages: 2

Brand: Ubiquiti Pages: 20

Super Hi-Q Loop

Brand: MFJ Pages: 14

Brand: Labgear Pages: 1

Brand: Ventenna Pages: 2

ETS-Lindgren 3147

Brand: ESCO Technologies Pages: 49

Pro Dual Band Soft Antenna

Brand: dji Pages: 30

Rosemount 5900S Series

Brand: Emerson Pages: 298

Brand: Sirio Antenne Pages: 2

Brand: Sea Tel Pages: 10

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 7

Brand: Philips Pages: 8

Brand: Philips Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands