background image

GB

 

 

21

Every 20 hours 

Check the level of the oil in the gearbox. The level 
must be between the maximum and minimum notch 
on the dip-stick (1). 

NOTE 

Check the oil level with the motor cold and with the 
two-wheel tractor on level ground. 

Every 300 hours 

Change the gearbox and transmission oil following 
the instructions given in the above paragraph cover-
ing running in.  

POWER TAKE OFF 

Every 8 hours 

Grease the PTO (see fig. 22, item 1 and 2) . 
Also grease the PTO every time you fit a new attach-
ment. 

 

CHECKS AND ADJUSTMENTS 

CLUTCH LEVER 

The clutch lever must have a free play of about 5 to 6 
mm before the clutch starts to disengage. 
Insufficient play can cause clutch slip, while excess 
play can lead to failure to disengage fully. 
Adjust play by means of cable adjuster (fig. 23, item 
1). 

DIFFERENTIAL LOCK LEVER 
(Special versions) 

If differential lock lever movement proves insufficient 
to fully unlock the differential, adjust the cable by 
means of adjuster (fig. 23, item 2) to obtain correct 
differential operation. 

BRAKE LEVERS (Special versions) 

The brake levers should have a free play of about 5 to 
6 mm. 
As brake linings wear, play will increase. 
Turn cable adjusters (fig. 23, items 3 and 4) to reduce 
play to the required value. 

NOTE 

The two brake cables should be adjusted to give si-
multaneous and uniform braking of both wheels. 

 

Summary of Contents for REV. 1000 Diesel (2+2)

































Reviews: