2. Hex. head bolt
4. Outside flange
6. Lower guard
8. Safety guard
10. Inside flange
12. Depth adjustment knob
14. Angle adjustment knob
16. Safety lock button
18. Battery pack
(Not included)
20. Laser guide
1. Lock lever
3. Wrench
5. Washer
7. Lower guard lever
9. Saw Blade
11. Cutting line
13. Base plate
15. Trigger
17. Saw guide fence
19. Battery clip
21. Laser on/off button
Li-ion batteries must be recycled.
Take the battery to the shop from which it was purchased as
soon as the post-charging battery life becomes too short for
practical use.
Do not discard the exhausted battery.
DESCRIPTION
DISPOSAL OF THE EXHAUSTED BATTERY
Wrench
，
Saw guide fence
STANDARD ACCESSORIES
APPLICATIONS
Blade diameter ....................................................... 165mm
(Only blades of this diameter may be used.)
Blade bore diameter ................................................ 20mm
Max. cutting capacities
at 90° .......................................................
52mm
at 45°
....................................................... 36
mm
Motor ..................................................................... DC 18V
No load speed ................................................... 4,000min
-1
Net weight (not incl. battery pack) ....…….…..........…2.4kg
SPECIFICATIONS
COMPATIBLE BATTERY PACK AND CHARGER
REMOVING
ADJUSTING THE CUTTING DEPTH (Fig. 4 )
(Use only for the purposes listed below.)
1. Sawing wood.
(The mark on the blade should be visible from the outside.)
1. Pushing the lock lever, turn the hex. head bolt with the
wrench until the gear shaft locks.
2. Loosen the hex. head bolt by turning the wrench
counterclockwise while pushing the lock lever.
3. Remove the hex. head bolt, washer and the outside flange.
4. Retract the lower guard back as far as possible toward
the safety guard, then remove the saw blade.
1. To adjust the cutting depth, loosen the depth adjustment
knob (12).
2. Slide the base plate (13) to the desired depth and
retighten the nut securely.
3. The cutting depth can be determined by measuring the
distance between the blade protrusion and the base plate.
ADJUSTING THE CUTTING BEVEL (Fig. 5)
1. The true cutting angle may be adjusted to any desired
angle between 0° and 45°.
2. Loosen the angle adjustment knob (14) which are positioned
at the front of the tool and move the base plate (13) to the
desired angle according to the bevel scale.
3. After adjusting the desired angle, be sure to retighten the
angle adjustment lever firmly.
Press the laser on/off button (21), the laser guide (20) generates
a red laser beam on the work surface in front of the saw.
Use the laser to guide the saw along the line of cut.
LASER GUIDE (Fig. 6)
SWITCH
This device is equipped with a safety switch. The device will
not switch on unless the safety lock button (16) is depressed.
To switch the device on press and hold the safety lock button
(16) then pull the trigger (15), releasing the trigger will switch
it off. If your finger is released from the switch, the safety lock
button will automatically return to the center position,
preventing the device from being switched on.
WARNING!
Instructions not to use any abrasive wheels.
ATTACHING
2. Loosen the hex. head bolt by turning the wrench
counterclockwise while pushing the lock lever. (Fig. 1)
3. Remove the hex. head bolt, washer (5) and the outside flange (4).
4. Retract the lower guard (6) back with the lower guard
lever (7) as far as possible toward the safety guard (8). (Fig. 3)
5. Then, attach the saw blade (9) against the flange (10) on
the gear shaft and then the outside flange and the hex.
head bolt. (Figs. 2 and 3)
6. Push the lock lever again, tighten the hex. head bolt by
turning the wrench clockwise while pushing the lock lever.
7. After tightening the hex. head bolt, release the lock lever.
BATTERY PACK (not included) ...... XB-1500, XB-3000
CHARGER (not included) ............... XPP-2700
ASSEMBLY INSTRUCTIONS
BE SURE TO DISCONNECT THE TOOL FROM THE
POWERSUPPLY BEFORE ATTACHING AND REMOVING
THE SAW BLADE.
BE SURE THAT THE TEETH OF THE SAW BLADE ARE
POINTING UPWARD AT THE FRONT OF THE TOOL.
ATTACHING AND REMOVING THE BLADE ( Figs. 1, 2 and 3 )
5
1. Pushing the lock lever (1), turn the hex. head bolt (2) with
the wrench (3) until the gear shaft locks. (Fig. 1)
If unexpected machine cut off happens during the
operation, press the button (21) TWICE to activate
the laser guide (20) again.
NOTE:
