background image

10

11

ASSEMBLY

WARNING:

Gasoline and its vapors are highly flammable and explo-
sive. To prevent serious personal injury and property dam-
age, handle it with care. Keep away from ignition sources, 
handle outdoors only, do not smoke while mixing gasoline 
and oil together; and wipe up spills immediately.

MIXING THE FUEL

See Figure 6.

The cultivator is powered by a two-stroke, air-cooled engine 
and requires a fuel mixture of gasoline and 2-cycle fuel oil.

NOTE:

  Always mix two-cycle engine oil like Ryobi’s Exact Mix 

Semi Synthetic Oil with gasoline before fueling the unit. Run-
ning the cultivator on gasoline alone will ruin the engine.
Use  a  mixture  of  50  parts  unleaded  regular  gasoline  and 
1 part two-stroke engine oil (50:1). Use branded 87 octane 
(R+M+2) unleaded gasoline or gasohol (maximum 10% ethyl 
alcohol, or 15% MTBE, no methyl alcohol.)

NOTE: 

Always mix oil and gas in the proper proportions: 

2.6 ounces of oil to one gallon of unleaded gasoline.
To mix the oil and fuel together for use:

n

  Pour 1/2 gallon of gasoline into a clean gas can or other 

container approved for fuel storage. Do not mix the fuel 
and oil directly in the cultivator’s fuel tank.

n

  Add 2.6 ounces of two-cycle engine oil to the gasoline 

mixture.

n

  Add the remaining 1/2 gallon of gasoline.

n

  Close the container holding the gas/oil mix and swirl the 

can to blend contents together.

NOTE:

  Do not mix more than you will use in a month, and 

shake the container to blend thoroughly before each use. 
Using  an  old  fuel  mixture  can  cause  starting  difficulty  or 
engine damage.

Fig. 6

1 Gallon           +         2.6 oz.         = 

     50:1

ADDING FUEL TO CULTIVATOR

See Figure 7.

When adding fuel to the cultivator, make sure the unit is sit-
ting on level ground and that the engine is not hot. 
Fuel only with recommended 50:1 mixture of gasoline and 
oil as described in “Mixing the Fuel.”
To add fuel to the cultivator:

n

  Clean area around fuel tank cap, if necessary.

n

  Remove the fuel tank cap.

n

  Insert a clean funnel into the fuel tank.

n

  Slowly pour gasoline/oil mixture into fuel tank. 

 

NOTE:

  Fill tank no higher than 1/2 in. from top to allow 

for gasoline expansion.

n

  Reinstall fuel cap.

n

   Clean up any spills.

FUEL TANK 

CAP

Fig. 7

Summary of Contents for RY60511A























Reviews: