background image

8

9

n

  Pull apart the ends of the bracket to expand slightly.

n

  Slide the bracket over the power head shaft immediately 

behind the “J” Barrier Handle. 

n

  Squeeze bracket ends together to retighten.

n

  Reinstall the bolt, lock washer, and hex nut to secure.

n

  Connect the latch on the shoulder harness to the strap 

hanger.

ASSEMBLY

CONNECTING THE POWER HEAD TO THE 

PRUNER ATTACHMENT

See Figure 4.

The pruner attachment connects to the power head by means 
of a coupler device. 

To install the attachment:

n

  Loosen the knob on the coupler of the power head shaft 

and remove the end cap from the attachment.

n

  Push in the button located on the shaft of the pruner at-

tachment. Align the button with the guide recess on the 
power head coupler and slide the two shafts together. 
Rotate extension shaft until button locks into the posi-
tioning hole.

 

NOTE:

  The attachment should only be operated with the 

blade in a vertical position. If the button does not release 
completely in the positioning hole, the shaft is not locked 
into place. Slightly rotate from side to side until the button 
is locked into place.

n

  Tighten the knob securely. 

CHAIN OILER

Add bar and chain oil in the chain oiler tank before starting 
the engine of the power head.

FUELING AND REFUELING THE PRUNER

FUEL MIXTURE

This product is powered by a 2-cycle engine and requires pre-
mixing gasoline and 2-cycle oil.  Pre-mix unleaded gasoline 
and 2-cycle engine oil in a clean 1 gallon container approved 
for gasoline.

n

  This engine is certified to operate on unleaded gasoline 

intended for automotive use.

n

  Mix high quality 2-cycle engine oil at 2.6 oz. per gallon.

n

  Do not use automotive oil or 2-cycle outboard oil.

n

  DO NOT mix quantities larger than usable in a 30-day 

period.

Fig. 4

COUPLER

KNOB

PRUNER

ATTACHMENT

POWER HEAD

SHAFT

POSITIONING 

HOLE

GUIDE 

RECESS

BUTTON

To remove:

n

  Loosen the knob.

n

  Push in the button and twist the shafts to remove and 

separate ends.

Fig. 3

SHOULDER 

STRAP

LATCH

LOCK NUT

 BOLT

STRAP

HANGER

“J” BARRIER

HANDLE

NUT

 BOLT

LOCK

WASHER

NUT

 BOLT

FIG. A

FIG. B

PREMIUM EXACT MIX™ (50:1)

  GASOLINE 

OIL

  1 Gallon (US) 

2.6 oz.

 

1 Liter 

20 cc (20 ml)

Summary of Contents for RY52003























Reviews: