background image

17

WARRANTY

THE FOLLOWING CALIFORNIA AIR RESOURCES BOARD (CARB) STATEMENT ONLY APPLIES TO MODEL NUM-
BERS REqUIRED TO MEET THE CARB REqUIREMENTS.

The U.S. Environmental Protection Agency (EPA), the California Air Resources Board 

(CARB), and Techtronic Industries North America, Inc., are pleased to explain the 

Emissions Control System Warranty on your 008 model year non-road or small off-

road engine. In California, new equipment that uses small off-road engines must be 

designed, built, and equipped to meet the state’s stringent anti-smog standards. In 

other states, new 000 and later model year non-road engines must be designed, 

built, and equipped at the time of sale to meet the U.S. EPA regulations for small 

non-road engines. The non-road engine must be free from defects in materials and 

workmanship which cause it to fail to conform with U.S. EPA standards for the first 

two years of engine use from the date of sale to the ultimate purchaser. Techtronic 

Industries North America, Inc., must warrant the emission control system on your 

non-road or small off-road engine for the period of time listed above provided there 

has been no abuse, neglect, or improper maintenance of your non-road or small 

off-road engine.
Your emission control system may include parts such as the carburetor or fuel injection 

system, the ignition system, catalytic converters, fuel tanks, valves, filters, clamps, 

connectors, and other associated components. Also included may be hoses, belts 

and connectors, and other emission-related assemblies.
Where a warrantable condition exists, Techtronic Industries North America, Inc., will 

repair your non-road or small off-road engine at no cost to you, including diagno-

sis, parts, and labor performed at an authorized service center for RYOBI

®

 brand 

outdoor products.

MANUFACTURER’S WARRANTY COVERAGE:

This product’s emissions control system is warranted for two years. If any emis-

sion-related part on your engine is defective, the part will be repaired or replaced by 

Techtronic Industries North America, Inc., free of charge.

OWNER’S WARRANTY RESPONSIBILITIES

(a)  As  the  non-road  or  small  off-road  engine  owner,  you  are  responsible  for 

the  performance  of  the  required  maintenance  listed  in  your  operator’s  manual. 

Techtronic  Industries  North  America,  Inc.,  recommends  that  you  retain  all  re-

ceipts  covering  maintenance  on  your  non-road  or  small  off-road  engine,  but 

Techtronic  Industries  North  America,  Inc.,  cannot  deny  warranty  solely  for  the 

lack  of  receipts  or  for  your  failure  to  ensure  the  performance  of  all  scheduled 

maintenance.  Any  replacement  part  or  service  that  is  equivalent  in  performance 

and  durability  may  be  used  in  non-warranty  maintenance  or  repairs,  and  shall 

not  reduce  the  warranty  obligations  of  Techtronic  Industries  North  America,  Inc.
(b) As the non-road or small off-road engine owner, you should be aware, however, 

that Techtronic Industries North America, Inc., may deny you warranty coverage if 

your non-road or small off-road engine or a part has failed due to abuse, neglect, 

improper maintenance, or unapproved modifications.
(c) You are responsible for presenting your non-road or small off-road engine to an 

authorized service dealer as soon as a problem exists. The warranty repairs should 

be completed in a reasonable amount of time, not to exceed 30 days.
If you have any questions regarding your warranty rights and responsibilities, you 

should contact a Techtronic Industries North America, Inc., Customer Representa-

tive at 1-800-860-4050.

DEFECT WARRANTY COVERAGE REqUIREMENTS:

(a) The warranty period begins on the date the engine or equipment is delivered to 

an ultimate purchaser. 
(b)  General  Emissions  Warranty  Coverage.  Techtronic  Industries  North  America, 

Inc., warrants to the ultimate purchaser and each subsequent purchaser that your 

non-road or small off-road engine is designed, built, and equipped at the time of sale 

to conform with all applicable regulations adopted by the California Air Resources 

Board or the United States Environmental Protection Agency; and that it is free from 

defects in materials and workmanship which cause the engine to fail to conform with 

applicable regulations for a period of two years from the date the non-road or small 

off-road engine is purchased by the initial purchaser. 
(c)  The  warranty  on  emissions-related  parts  will  be  interpreted  as  follows:  Any 

warranted part that is not scheduled for replacement as required in the Emissions 

Maintenance Schedule and Warranty Parts List set forth below is warranted for two 

years. If any such part (including any part that is scheduled only for regular inspection) 

fails during the period of warranty coverage, it will be repaired or replaced at any 

RYOBI

®

 Authorized Service Center at no charge. Any such part repaired or replaced 

under warranty will be warranted for the remaining warranty period. A statement to 

the effect of “repair or replace as necessary” would not reduce the period of war-

ranty coverage. Any warranted part that is scheduled for replacement as required 

maintenance  in  the  Emissions  Maintenance  Schedule  and  Warranty  Parts  List  is 

warranted for the period of time prior to the first scheduled replacement point for 

that part. Any such part repaired or replaced under warranty is warranted for the 

remainder of the period prior to the first scheduled replacement point, and will be 

repaired or replaced at any RYOBI

®

 Authorized Service Center for no charge until 

that replacement point is reached. 

Techtronic  Industries  North  America,  Inc.,  shall  remedy  warranty  defects  at  any 

authorized  RYOBI

®

  Authorized  Service  Center,  including  any  distribution  center 

that may be franchised to service the subject engines. Any diagnostic work done 

at a RYOBI

®

 Authorized Service Center shall be free of charge to the owner if such 

work determines that a warranted part is defective. Any manufacturer-approved or 

equivalent replacement part may be used for any warranty maintenance or repairs 

on emission-related parts, and must be provided free of charge to the owner if the 

part is still under warranty. Techtronic Industries North America, Inc., is liable for 

damages  to other  engine  components caused  by the  failure  of a  warranted  part 

still under warranty.
Add-on or modified parts that are not exempted by the California Air Resource Board 

may not be used. The use of any non-exempted add-on or modified parts will be 

grounds for disallowing a warranty claim. Techtronic Industries North America, Inc., 

will not be liable to warrant failures of warranted parts caused by the use of a non-

exempted add-on or modified part. 
The California Air Resources Board’s Emission Warranty Parts List specifically defines 

the emission-related warranted parts. (EPA’s regulations do not include a parts list, 

but the EPA considers emission-related warranted parts to include all the parts listed 

below.) Techtronic Industries North America, Inc., will provide any documents that 

describe its warranty procedures or policies within five days upon request by the 

California Air Resources Board.

EMISSIONS PARTS LIST

Emissions parts vary from product to product. Your emissions control system warranty 

applies to any of the following components that may be included on your product:
(1)  Fuel Metering System 
 

(i)  Carburetor  and  internal  parts  (and/or  pressure  regulator  or  fuel  injection 

system). 

 

(ii)  Air/fuel ratio feedback and control system.

 

(iii)  Cold start enrichment system.

 

(iv)  Fuel Tank.

()  Air Induction System
 

(i)  Controlled hot air intake system.

 

(ii)  Intake manifold.

 

(iii)  Air filter.

(3)  Ignition System
 

(i)  Spark Plugs.

 

(ii)  Magneto or electronic ignition system.

 

(iii)  Spark advance/retard system.

(4)  Exhaust Gas Recirculation (EGR) System
 

(i)  EGR valve body and carburetor spacer, if applicable. 

 

(ii)  EGR rate feedback and control system.

(5)  Air Injection System
 

(i)  Air pump or pulse valve.

 

(ii)  Valves affecting distribution of flow.

 

(iii)  Distribution manifold.

(6)  Catalyst or Thermal Reactor System
 

(i)  Catalytic converter.

 

(ii)  Thermal reactor.

 

(iii)  Exhaust manifold.

(7)  Particulate Controls
 

(i)  Traps, filters, precipitators, and any other device used to capture particulate 

emissions.

(8)  Miscellaneous Items Used in Above Systems
 

(i)  Electronic controls.

 

(ii)  Vacuum, temperature, and time sensitive valves and switches. 

 

(iii)  Hoses, belts, connectors, and assemblies.

Techtronic Industries North America, Inc., will furnish with each new engine written 

instructions for its maintenance and use by the owner.
The Emissions Compliance Period referred to on the Emissions Compliance label 

indicates the number of operating hours for which the engine has been shown to 

meet  Federal  emission  requirements.  Category  C=50  hours,  B=15  hours,  and 

A=300 hours.

TECHTRONIC INDUSTRIES NORTH AMERICA, INC., LIMITED WARRANTY STATEMENT FOR FEDERAL  

AND CALIFORNIA EMISSION CONTROL SYSTEMS NON-ROAD AND SMALL OFF-ROAD ENGINES
YOUR WARRANTY RIGHTS AND OBLIGATIONS

Summary of Contents for RY08576





















Reviews: