Ryobi RY08554 Operator'S Manual Download Page 13

13

on/oFF SWiTch

OPERATION

STARTING AND STOPPING

See Figures 9 - 10.

To start a cold engine:
DO NOT
 squeeze the throttle trigger until the engine starts 
and runs.

 

Lay the blower/vacuum on a flat, bare surface.

 

 

PRIME - Press the primer bulb 7 times.

 

SET the start lever to the START position.

 

PULL the starter grip until the engine starts.

 

Wait 6-10 seconds, then squeeze the trigger to run.   

NOTE: Squeezing and releasing the throttle trigger releases 
the start lever to the 

RUN position.

To start a warm engine:
PULL
 the starter grip until the engine starts.

To stop the engine:
Press and hold the switch in the stop “   ” position until 
the engine stops.

Fig. 9

primer 

bulb

choke 

leVer

ThroTTle 

TriGGer

Fig. 11

STArTer 

Grip

proper operATinG poSiTion

Fig. 10

OXYGENATED FUELS

Some conventional gasolines are blended with alcohol or an 
ether compound. These gasolines are collectively referred 
to as oxygenated fuels. To meet clean air standards, some 
areas of the United States and Canada use oxygenated fuels 
to help reduce emissions.
If using an oxygenated fuel, make sure it is unleaded and 
meets the minimum octane rating requirements. Before using 
an oxygenated fuel, try to confirm the fuel’s contents. Some 
states/provinces require this information to be posted on the 
pump. The following are the EPA approved percentages of 
oxygenates:
Ethanol  (ethyl  or  grain  alcohol)  10%  by  volume.  You 
may use gasoline containing up to 10% ethanol by volume. 
Gasoline  containing  ethanol  may  be  marketed  under  the 
name “Gasohol.” 

Do not use E85 fuel.

MTBE (methyl tertiary butyl ether) 15% by volume. You 
may use gasoline containing up to 15% MTBE by volume.
Methanol (methyl or wood alcohol) 5% by volume. You 
may use gasoline containing up to 5% methanol by volume 
as long as it also contains cosolvents and corrosion inhibitors 
to protect the fuel system. Gasoline containing more than 5% 
methanol by volume may cause starting and/or performance 
problems.  It  may  also  damage  metal,  rubber,  and  plastic 
parts of the product or your fuel system.
If you notice any undesirable operating symptoms, try another 
service station or switch to another brand of gasoline.
NOTE:  Fuel  system  damage  or  performance  problems 
resulting from the use of an oxygenated fuel containing more 
than the percentages of oxygenates stated previously are 
not covered under warranty. 

Summary of Contents for RY08554























Reviews: