Ensure that you read, understand, and apply the
safety instructions.
Reminder: DO NOT vacuum hazardous substances.
The use of an incorrect dust bag will invalidate the
warranty.
Ensure that the power cord is disconnected from the
outlet.
DRY VACUUMING
Ensure that the HEPA cartridge filter is completely mounted.
Ensure that the filter is inserted all the way. (Fig. 13)
Verify that the dust bag is installed to the inside of the
tank (Fig. 8).
Replace the top section on the tank, and secure it in
place using the clamps (Fig. 10).
Insert the larger end of the hose into the front inlet on the
tank and lock it in place. Push the required attachment
on to the free end of the hose or extension (Fig.12).
Plug the power cord in to the power outlet.
Turn the motor on by flipping the switch to the ‘I’ (ON)
position (Fig. 14).
Once you have finished vacuuming, flip the switch to the
‘O’ (OFF) position and unplug the power cord from the
power outlet. (Fig. 15)
DO NOT USE THE HEPA CARTRIDGE FILTER FOR WET
OR SHARP MATERIALS.
DO NOT USE DUST BAG FOR LIQUID VACUUMING.
WARNING
WARNING
OPERATION
WET VACUUMING
For dry vacuuming, install the supplied dust filter and
dust bag (Fig. 7, Fig. 8).
For wet vacuum cleaning, install the supplied foam filter
only (Fig. 9).
Replace the top section on the tank (Fig. 10).
Align the top section with the clamps and snap into place
by applying pressure until clamps click (Fig. 10).
Insert the large end of the hose into the front inlet of the
tank and turn to lock (Fig. 11).
Fit the required accessory on to the suction tube (Fig. 12).
3
Ensure that the power cord is disconnected from the
power outlet.
Ensure that the tank is clean and free of dust and dirt.
Remove the HEPA cartridge filter and dust bag, and install a
foam filter over the filter basket and place the top section
back on the tank (Fig. 9).
DO NOT use the HEPA cartridge filter for wet or sharp materials.
Fit the desired nozzle to the vacuum hose (Fig. 12).
Ensure that the switch is in the ‘O’ (OFF) position before
plugging the power cord into the power outlet.
Turn the motor on by flipping the switch to the “I” (ON)
position (Fig. 14).
After use, flip the switch to the “O” position (Fig. 15) and
unplug the power cord, then empty and dry the tank
(Fig. 16).
BLOWER OPERATION
The foam filter must be removed after wet vacuuming,
and a HEPA cartridge filter must be installed before dry
vacuuming again.
WARNING
Always wear safety goggles before using blower.
WARNING
Wear a dust mask if blowing creates dust that might
be inhaled.
WARNING
Keep bystanders clear from blowing debris.
WARNING
Ensure that you read, understand, and apply the
safety instructions.
Reminder: DO NOT vacuum hazardous substances.
WARNING
When vacuuming large quantities of liquids, do not immerse
the nozzle completely in the liquid; leave a gap at the tip of
the nozzle opening to allow air inflow.
The machine is fitted with a float valve that stops the
suction action when the container reaches its maximum
capacity. You will notice an increase in motor speed.
When this happens, turn off the machine, disconnect from
power supply, and drain the liquid into a suitable receptacle
or drain. To continue vacuuming, refit the container with the
drain cap. After wet vacuuming, turn the machine off and
remove plug from power supply.
Empty the container, clean and dry the inside and outside
before storage.
This Wet/Dry Vac has blowing capabilities.
To use the blower feature follow the instructions listed.
IMPORTANT!
Improper filter assembly may cause motor failure.
Please refer to instruction below.
WARNING
DRY VACUUMING
+
WET VACUUMING
Paper Bag
Foam Filter
Cartridge Filter
Summary of Contents for RVC1218P-P
