![background image](http://html1.mh-extra.com/html/ryobi/rsc-450/rsc-450_owners-operating-manual_1505436004.webp)
THANK YOU FOR BUYING A RYOBI PRODUCT.
To ensure your safety and satisfaction, carefully read
through this OWNER’S MANUAL before using the
product.
3
General Safety Rules
SAVE THESE INSTRUCTIONS
WARNING!
Read all instructions Failure to follow all
instructions listed below may result in electric shock,
fire
and/or serious injury. The term “power tool” in all of the
warnings listed below refers to your mains-operated
(corded) power tool or battery-operated (cordless) power
tool.
• To operate this device safely, the user must have read
and understood these instructions for use before using the
device for the first time.
• Observe all safety instructions! Failure to do so may cause
harm to you and others.
• R
etain all instructions for use, and safety instructions for
future reference.
• If you sell or pass the device on, you must also hand over
these operating instructions.
• The device must only be used when it functions properly.
If the product or part of the product is defective, it must be
taken out of operation and disposed of correctly.
• Keep children away from the device! Keep the device out
of the way of children and other unauthorised persons.
• Do not overload the device. Do not use the device for
purposes for which it is not intended.
• Exercise caution and only work when in good condition: If
you are tired, ill, if you have ingested alcohol, medication
or illegal drugs, do not use the device, as you are not in a
condition to use it safely.
• T
his product is not intended to be used by persons
(including children) or who are limited in their physical,
sensory or mental capacities or who lack experience
and/or knowledge of the product unless they are
supervised, or have been instructed on how to use the
product, by a person responsible for their safety.
• Ensure that children are not able to play with the device.
• A
lways comply with all applicable domestic and
international safety, health, and working regulations.
When used for its intended purpose, this
device corresponds
to the state of the art, as well as to the current safety
requirements at the time of its introduction.
The spreader is intended for the distribution of fertilisers,
seed, winter spreading material, and similar in the garden
and on non-commercial pieces of land.
Th
e device is not suitable for commercial or industrial use.
A
ny other type of use is inappropriate. Improper use or
modifications to the device or the use of components that
are not tested and approved by the manufacturer may result
in unforeseen damage!
An
y use that deviates from its intended use and is not
included in these instructions is considered unauthorised use
and relieves the manufacturer from his or her legal liability.
• When filling the container with fertiliser or granulates
containing herbicides, load only the amount needed in
the short term.
• W
hen spreading fertiliser or granulates containing
herbicides, follow the instructions and warnings
provided
by the manufacturer. Avoid contact with eyes and skin.
If contact occurs, wash thoroughly with water. If it
comes
into contact with the eyes, seek medical assistance
immediately.
• Do not leave the spreader unsupervised.
DESCRIPITION
SPECIFICATIONS
ASSEMBLY
SEEDING CART SAFETY PRECAUTIONS
INTENDED USE
Capacity:
Spreading size:
Working width:
Wheel diameter:
Handle diameter:
Net weight:
12L
0-8mm
450mm
197mm
20mm
2.3kg
1. Upper handle
2. Lower handle
3. Intermediate piece
4. Wheel cap
5. Wheel
6. Spreader
7. Support leg
8. Spreading quantity adjust lever
INSTALL THE WHEELS (Fig. 1)
1. Fit the wheel (5) onto axis and then tighten by using
M5x10 screw and M5 flat washer.
2. Put on wheel cap (4).
3. Repeat on other side.
ASSEMBLE THE HANDLE
1. Insert upper handle (1) into lower handle (2). (Fig. 2)
2. Locate the whole handle on intermediate piece B.
(Fig. 3, Fig. 4)
3. Screw intermediate piece A to B by using six ST4.2x13
screws. (Fig. 3, Fig. 4)
4. Locate the handle into spreader, tighten by using two
ST5.2x9.5 screws. (Fig. 5)
INSTALL THE SUPPORT LEG (Fig. 6)
1. Insert the support leg (7) into spreader (6) as shown;
2. Tighten by using ST4.2x13 screw and M4 flat washer.
Summary of Contents for RSC-450
