Ryobi RPW140-G, Original Instructions Manual

Page: 4 / 26

2
manufacturer.
ELECTRICAL SAFETY WARNINGS
■ The plug must match the outlet. Never modify the plug
in any way. Unmodified plugs and matching outlets
reduces the risk of electric shock.
■ Do not use the product if the power cord or other
important parts, such as safety devices, are damaged.
■ Only use a weather proof extension cord. Check the
extension cord before every use for damage. Always
uncoil the extension cord during the use because
coiled cords can overheat. Damaged extension cords
should not be repaired, they should be replaced with
an equivalent type.
■ Keep the power cord away from heat, oil, and sharp
edges.
■ Never touch the mains plug and the socket with wet
hands.
■ Inadequate extension cords can be dangerous. If an
extension cord is used, it shall be suitable for outdoor
use, and the connection has to be kept dry and off the
ground. Use a cord wheel to keep the socket at least 60
mm above the ground.
■ Electric power shall be supplied with a residue current
device (RCD) with a tripping current of not more than
30mA.
ADDITIONAL SAFETY WARNINGS
■ Some regions have regulations that restrict the use of
the product in some operations. Check with your local
authority for advice.
■ Before each use, check for damage. A damaged high-
pressure hose must be replaced immediately. Ensure
all connections, such as high-pressure hose and
nozzle, are secure. Unwind the hose properly so they
may not get twisted or kinked.
■ Do not allow children or untrained individuals to use the
product.
■ Before starting any cleaning operation, close doors and
windows. Clear the area to be cleaned of debris, toys,
outdoor furniture, or other objects that could create a
hazard.
■ Never pick up or carry the product while the motor is
running.
■ Do not use the product in temperatures below 0°C.
■ Do not use acids, alkalines, solvents, flammable
material, bleaches, or industrial grade solutions in the
product. These products can cause physical injuries to
the operator and irreversible damage to the product.
■ Always operate the product on a level surface.
WARNING
High-pressure jet can be dangerous if subject to misuse.
The jet must not be directed to people, animals, electrical
devices, or the product itself.
■ Hold the handle securely with both hands. Expect
the handle to move when the trigger is pulled due to
reaction forces. Failure to do so could cause loss of
control and injury to yourself and others.
■ Make sure the air in the hose and pump is released
before you turn on the product. To remove the air in
the hose and pump, connect the water supply to the
pump using a garden hose, connect the trigger handle
to pump using the high-pressure hose, disengage the
trigger handle lock, and press the trigger until there is
a steady flow.
■ Exercise caution to avoid slipping or falling.
■ Keep firm footing and balance. Do not overreach.
Overreaching can result in loss of balance.
■ Only use accessories that are recommended by the
manufacturer. The use of improper accessories may
cause injury.
■ Never leave the product running unattended. Turn the
product off. Do not leave the product until it comes to
a complete stop.
■ Be familiar with the controls. Know how to stop the
product and bleed the pressure quickly.
■ Stay alert and exercise control. Watch what you are
doing and use common sense.
■ Do not use the product when you are tired, ill, or
under the influence of drugs, alcohol, or medication. A
moment of inattention while operating the product may
result in serious personal injury.
■ Do not use the product if the switch does not turn it on
and off. Any product that cannot be controlled with a
switch is dangerous and must be repaired.
■ Keep a minimum distance of 30 cm when cleaning
vehicles. The high-pressure jet may damage or burst
vehicle tires and/or tire valves.
■ Use a garden hose with a maximum length of 15 m and
minimum diameter of 18 mm (3/4 in.)
CAUTION
Water blasting any asbestos-containing material,
including an asbestos oil, is illegal.
OVERLOAD PROTECTION
A thermal sensor protects the product from overloading.
The product will automatically shut the power down while
overheating. To resume operation, disconnect the product
from the power supply, wait for about 15 min to cool down,
and reconnect the product to the power supply.