background image

11

 

Use a screwdriver to push the blade into the blade 
holder until it is centred into position.

 

Depress the spring-loaded blade guard.

 

Insert the blade holder into the cutter block assembly.

 

Retighten the three blade securing screws using the 
blade wrench.

 

Repeat the above procedure to change the other blade.

REPLACING THE BELT

See Figures 15 - 16.

When replacing the belt, use the recommended 
replacement belt only.

 

Unplug the planer.

 

Remove belt cover screws.

 

Remove the belt cover.

 

Force the old belt from the small pulley by turning in the 
direction shown. As you turn the belt, pull and work it off 
the small pulley until it has been completely removed 
from both pulleys.

 

Install the new belt over the large pulley. As you turn 
the belt, push and work it onto the small pulley until it 
is in place.

 

Replace the belt cover.

 

Install belt cover screws and tighten securely.

NOTE:

 Do not overtighten the screws.

ENVIRONMENTAL PROTECTION

Recycle raw materials instead of disposing 
of as waste. The machine, accessories and 
packaging should be sorted for environmental-
friendly recycling.

SYMBOLS

Safety alert

V

Volts

Hz

Hertz
Alternating current

W

Watts

n

o

No-load speed
Revolutions or reciprocations per minute

Regulatory Compliance Mark (RCM). Product 
meets applicable regulatory requirements.

Please read the instructions carefully before 
starting the machine.

Wear eye protection

Class II tool, double insulation

Maximum planing capacity

Maximum planing capacity

Waste electrical products should not be 
disposed of with household waste. Please 
recycle where facilities exist. Check with your 
Local Authority or retailer for recycling advice.

Summary of Contents for RPL780

















Reviews: