![background image](http://html1.mh-extra.com/html/ryobi/rlt3025f/rlt3025f_operators-manual_1507179003.webp)
2
ENGLISH (Original Instructions)
n
Do not abuse the power cord. Never pull the cord to
disconnect the tool from the power point. Keep the
cord away from heat, oil and sharp edges.
n
Look after your tools. Keep tools clean for better
and safer performance and follow the instructions
regarding lubrication and accessory changes. Inspect
extension cords periodically and replace them if
damaged. Keep tool handles dry, clean and free from
oil and grease.
n
Disable idle tools. Switch off the power and
disconnect the plug from the power before servicing,
when changing accessories and when the tool is not
in use.
n
Avoid unintentional starting. Always check that the
switch is in the OFF position before plugging in the
tool to the power supply. Do not carry a plugged in
tool with your finger on the switch.
n
Use outdoor rated extension cords. Use only
extension cords that are intended for outdoor use
and are so marked. It is advised to use an residual
current device (RCD) when using an extension cord
outdoors.
n
Stay alert. Watch what you are doing. Use common
sense. Do not operate a power tool when you are
tired.
n
Check for damaged parts. Before using a tool,
check that there are no damaged parts. If a part is
slightly damaged, carefully determine if it will operate
properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts,
mounting and any other conditions that may affect
the operation of the tool. A guard or other part that is
damaged should be properly repaired or replaced by
an service centre unless otherwise indicated in this
manual.
n
Defective switches must be replaced by an
authorised service facility. Do not use a tool if the
switch does not turn the tool on and off correctly.
n
Guard against electric shock. Avoid body contact with
‘grounded’ objects such as water pipes, radiators,
cookers and refrigerator enclosures.
n
Use only approved parts. When servicing, use only
identical replacement parts. Use an authorised
service facility to fit replacement parts. The use of
improper accessories or attachments could lead to
personal injury.
n
Be aware of the harmful/toxic dusts arising from grass
trimming (e.g. fertilizers, insecticides, etc.) .
n
This electric tool is constructed in accordance with
the relevant safety requirements. Only experts may
repair the electric tool.
n
Make sure the voltage of the power supply is correct
for your machine. The voltage of this machine is
stated on the rating plate.
n
When installing the grass shield during assembly,
beware of its sharp cutting edge.
n
Never hold the cutter head above foot height or point
it towards people or animals when in use.
n
If the trimmer starts to vibrate excessively, switch it off
immediately. Have it checked by a qualified service
engineer.
n
Remove any sticks, stones and debris from the
working area before using the trimmer.
n
Keep hands and feet away from the cutting edge at
all times, especially when the motor is running.
n
Do not operate the trimmer on roads or gravel paths.
n
When working on a steep slope, cut across the slope.
Do not operate the trimmer along the slope.
n
Never run while using the trimmer.
n
Never fit a metal replacement line.
n
Use the trimmer in daylight or good artificial light.
Never use when visibility is poor.
n
Do not overreach, keep proper footing and balance at
all times.
n
After extending a fresh cutting line, always return
the machine to its normal operating position before
switching it on.
n
Always ensure the ventilation openings are kept clear
of debris.
n
If the power cord is damaged during use, disconnect
it from the power supply immediately. Do not touch
the cord before disconnecting the supply.
n
The appliance should be supplied via a RCD with
tripping current not more than 30mA.
SPECIFIC SAFETY RULES
SPECIFIC TRIMMER SAFETY
n
Replace the trimmer head if it is cracked, chipped or
damaged in any way. Ensure it is properly installed
and securely fastened.
n
Make sure all guards, deflectors and handles are
properly and securely attached.
n
Use only the manufacturer's replacement line in the
trimmer head.
n
Use the product for cutting grass and light weeds
only. Do not use for any other purpose.
n
Before starting the product, position it so that the
cutting line does not come in contact with anything
you do not intend to cut.
n
Maintain a firm grip on both handles while trimming.
Keep the trimmer head below waist level. Never cut
with the trimmer head placed over 76 cm above the
ground.