Ryobi RLT1038X, Original Instructions Manual

Page: 3 / 21

Safety
1
GENERAL SAFETY WARNINGS
WARNING
When using the product, the safety rules must be
followed. For your own safety and that of bystanders,
please read these instructions before operating the
product. Please keep the instructions safe for later use.
WARNING
The product is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
Children should be supervised to ensure that they do not
play with the product.
TRAINING
Ŷ
Never allow children or people unfamiliar with these
instructions to operate the product.
Ŷ
Keep the area clear of all bystanders, children and pets
while using the product. Switch off the product if anyone
enters the area.
Ŷ
Never operate the product when you are tired, ill or
under the influence of alcohol, drugs or medicine.
Ŷ
Use the product for cutting grass and light weeds only.
Do not use for any other purpose.
Ŷ
Keep in mind that the operator or user is responsible
for accidents or hazards occurring to other people or
their property.
ELECTRICAL
Ŷ
Avoid unintentional starting. Always check that the
switch is in the off position before plugging in the
product to the power supply. Do not carry a plugged in
tool with your finger on the switch.
Ŷ
Electrical power should be supplied via a residual
current device (RCD) with a tripping current of not more
than 30 mA.
Ŷ
Before use, examine the power cord or extension cable
for damage. If there are signs of damage, it must be
replaced by a qualified service technician.
Ŷ
Do not use the product if the electric cables are
damaged or worn.
Ŷ
If the power cord or extension cable becomes
damaged during use, disconnect from the power supply
immediately. Do not touch the electric cables until the
power supply has been disconnected. Do not repair.
Replace only with identical electric cable.
Ŷ
Extension cable must be uncoiled during use. Coiled
cables can overheat.
Ŷ
Make sure the power cord is positioned so that it will not
be stepped on, tripped over or otherwise subjected to
damage or stress.
Ŷ
Never carry the product by the power cord.
Ŷ
Never pull by the power cord to disconnect from the
power supply.
Ŷ
Keep the power cord away from heat, oil and sharp
edges.
Ŷ
Make sure voltage is correct for the product. A
nameplate on the product indicates the unit’s voltage.
Never connect the product to an AC voltage that differs
from this voltage.
Ŷ
Make sure the switch is in the off position before
disconnecting from power supply.
Ŷ
For storage, always disconnect from power supply and
wind cable.
PREPARATION
Ŷ
Always wear protective non-slip footwear and long
trousers.
Ŷ
Before use, check that there are no damaged parts. A
defective switch or any part that is damaged should be
properly repaired or replaced by an authorized service
facility.
Ŷ
Consider the environment in which you are working.
Keep the working area free from wires, sticks, stones
and debris.
Ŷ
Make sure the head attachment is properly installed
and securely fastened.
Ŷ
Make sure all guards, deflectors and handles are
properly and securely attached.
OPERATION
Ŷ
To avoid using the product in bad weather especially
when there is a risk of lightning.
Ŷ
Use the product in daylight or good artificial light.
Ŷ
Avoid using on wet grass.
Ŷ
Keep proper footing and balance at all times.
Ŷ
Do not walk backwards when using the product.
Ŷ
Walk, never run.
Ŷ
Keep the head attachment below waist level.
Ŷ
Do not cut on surfaces other than grass on ground.
Ŷ
Never operate the product with damaged guards or
without guards in place.
Ŷ
Never fit a metal replacement line.
Ŷ
Keep hands and feet away from the cutting means at
all times and especially when switching on the product.
Ŷ
Never pick up or carry the trimmer by the electric cable.
Ŷ
Beware of objects thrown by the cutting line.
Ŷ
Switch off and disconnect from the power supply before:
– servicing
– leaving the product unattended
– cleaning the product
– changing accessories